Podcasting since 2005! Listen to Latest SolderSmoke

Wednesday, February 12, 2014

A Very Simple SSB Transmitter

 
 
I found this in the files section of the BITX20 Yahoo Group.  There is no information on the source.  I see two balanced modulators and two very simple phase shift networks. 


Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

6 comments:

  1. Bill - Looks like a solid state version of ZL2AMJ's first Tucker Tin (c1962) - the two tube SSB transceiver designed for use with a carbon microphone. Also one of the Doug Demaw books (QRP Notebook?) had a phasing SSB tx circuit as an idea to try but with few details. 73, Peter VK3YE

    ReplyDelete
  2. I was going to say, that simple a transmitter was not uncommon in the old days.

    One thing about using phasing for transmitting is that you have a controlled source. Actual voice is a small bandwidth, and you can use a limited bandwidth microphone and/or audio shaping to keep out extra frequencies like from fans.

    This means the phasing network doesn't have to handle wide bandwidth, indeed the worst that can happen with a simple phasing network is that you may put out something on the unwanted sideband.

    So those rigs were in effect a hybrid, better than DSB (that were also common for similar reasons) in that some of the other sideband was gone, but not that much more complicated. Though DSB had the advantage of being done at high levels, while most phasing rigs were done at low level and amplified.

    With a receiver, you're faced with all that is there on the band. If you don't knock out the sideband with a good phasing network, you get interference from the "audio image". And since there's nothing really to limit what the phasing network has to handle in the receiver, it has to be better than on a simple transmitter.

    I remember an article in "73" about ISB from 1977, it said something about how the phasing method wasn't likely to be useful. I read that again a few years after that, and realized that if you were sending RTTY on the other sideband, that would be so simple. You don't need a phasing network, just generate the tones with some circuit that puts out a quadrature output. Easier to start with the right signal than to put a regular oscillator through a phasing network. Of course, that really only works when you need only an oscillator output. Voice is too complicated.

    That was before phasing made a real comeback as serious transmitters, in between the early work on SSB and ore recent times, it was seen as a simple method for getting sideband.

    Michael

    ReplyDelete
  3. It looks almost identical to the one on page 164 of W1AW's QRP Notebook. He said it was his interpretation, from an old book, of a tube version, someone had asked him make a solid state version.

    ReplyDelete
  4. It is a worthless design. 1. It uses a pierce osc in a non frequency mobile format. It creates DSB NOT ssb. It uses not RF qualified transistors. 3. you would be lucky to get 200mW out of this design. Don't build it. I suggest if you want simplicty of DSB and frequency mobile you look at ozQRP.com and his 40M TRANSCEIVER DSB kit and copy his design for frequency of interests BUT get rid of the non RF transistor like BD 139 and subs 2n3866 for predriver and 2sc2116 CB type Ballasted 6W nominal Bipolar for the PA transistor and you might make 4 W at 14VDC supply (that is only 2 W SSB equivalent of course). Or buy the kit and make the approp subs as above. The kit is only about 65 USD as of 2018 and if you can get it supplied without the case you will save on postage. The 2n2222 design will only bring wasted money an tears. ...TEF

    ReplyDelete
  5. Hello! You can improve this device.You only needs move a speech spectrum from 0.3-3.5kHz to 4-7kHz. It allows to realize the transciever with a NAROWBAND and therefore simple phaseshifter and
    bandpass filter 4-7kHz.

    ReplyDelete

Designer: Douglas Bowman | Dimodifikasi oleh Abdul Munir Original Posting Rounders 3 Column