Just go to http://soldersmoke.com. On that archive page, just click on the blue hyperlinks and your audio player should play that episode.
http://soldersmoke.com
I had been sworn to secrecy for so long, I thought I was going to burst. I almost hinted at this in the last podcast. But I didn't. I kept the secret. But now Farhan has made public his latest creation:
Wow! Great stuff from Farhan. I love reading his circuit notes even though much of it passes right over my head.
He has such a good-natured approach to circuit design and his projects are practical and sensible in regards to performance, ease of construction and component choice.
Great job Bill on keeping the secret...there was a sly mention on the 10th anniversary Podcast of how long it had been since Farhan had visited the show, which makes me think the subject of this special project was slowly percolating towards the surface.
I so want to build this. I have a couple of CMOS Si570s left over from building SoftRock RxTx 6.3 and other SDRs. Too bad it won't work since it can only go up to 160MHz. :( However, I'm already developing my own DDS front end with a PIC microcontroller. Would be easy to swap it out with one out of the junk box that can connect to the PC with USB. Never had a reason to buy an Arduino yet. With the source code available, I'll probably stick with my own front end to save some money. Not counting PCB materials, I think I can build one for under $50 (also not counting junk box parts). What's a good source for inexpensive PCB for RF projects?
Having finished up my QSK VFO system for vintage Knight T-50 and Drake 2B (the latter being entirely Bill's fault), the bench is empty and needs a project. A spectrum analyzer to analyze crystal filters has been needed in my shack for a long time. The Arduino has now made this possible with low cost and high accuracy. Wow, Farhan. Obviously, it's time to start planning this next project! Congratulations.
"SolderSmoke -- Global Adventures in Wireless Electronics" is now available as an e-book for Amazon's Kindle.
Here's the site:
http://www.amazon.com/dp/B004V9FIVW
Free e-Book version of The ARRL Antenna Book
-
Many thanks to Alex (KR1ST), on Mastodon, who notes that the e-Book version
of The ARRL Antenna Book 25th Edition is free on the ARRL website. Simply
go t...
International sounds for the umbraphiles
-
Hi I’m FastRadioBurst 23 from the Imaginary Stations crew letting you know
about this week’s shows. The first broadcast is to Europe via Shortwave
Gold on...
March 28, 2024. Just another Day at the Office.
-
FT-8 with a RPi Zero W
Given the FT-8 achievement maybe even QUISK would work on the RPi Zero W
for a really small SDR Transceiver.
But all that g...
The GM3OXX “Oxo” Transmitter
-
As well as the small stash of finished projects that grace my living space,
I also have two small boxes containing various boards. Some of them are
boards ...
Handy breakout board for Raspberry Pi Pico
-
Just picked up a few of these breakout boards. I'm not sure that I like the
screw terminals but it is handy having LEDs on each GPIO pin. I'm really
gettin...
Repairing a dead Kenwood TS-850S
-
Recently, a Kenwood TS-850S - a radio from the mid-early 1990s - crossed my
workbench. While I'm not in the "repair business", I *do* fix my own
radios,...
A 51S-1 Restoration Story
-
I came across my Collins 51S-1 in a big junkyard in Ankara, Turkey around
2012. It was in a pile with a lot of other electronic scrap, probably from
one o...
New QRP Cluster Online From OM0ET and OM6APN
-
By DX EXPLORER
DX EXPLORER
Paul OM0ET and Peter OM6APN recently launched a new cluster dedicated to
QRP operations. Have a look and I hope you will enjoy...
3D Printing The Hadley 114mm Newtonian Telescope
-
Yes, we’re building a 3D Printed Newtonian Telescope called Hadley. It’s
being printed in PETG and in the video below, I give a quick tour. My build
isn’...
3D printed project boxes
-
I have been busy with some other things that have kept me away from
electronics projects for quite a while. Now I can get back to them, but
realize I n...
Daylight Again – An all Analog Radio
-
What’s all this? In 10 seconds, A high performance, 7MHz, 5 watt SSB rig
Draws just 24 mA of current 90 dB dynamic range, 80 dB close-in dynamic
range 3D ...
Adding Enclosure to your sBitx Boards Order
-
The early buyers of the sBitx board set who bought it for $270 USD might
want to also add the enclosure (box) for in the kit. What you will now get
is a f...
Digi-chirp! Digital synthesis of ‘nostalgic’ CW
-
The bottom ends of 80, 40 and 20m are not what they used to be. For
starters, the busiest part is the digital segment where computers talk to
computers – l...
-
A Simple Speech Processor
(For QRP/SSB Homebrew Transceivers )
Over the last few weeks I had been thinking to build a small AF speech
processor to add to...
A New Look for your uBitx!
-
Adding a "Cool Blue" Display to your uBitx!
The standard "green background" with black lettering frequently reminds me
that I suffer from Chronic seasickn...
Wow! Great stuff from Farhan. I love reading his circuit notes even though much of it passes right over my head.
ReplyDeleteHe has such a good-natured approach to circuit design and his projects are practical and sensible in regards to performance, ease of construction and component choice.
Great job Bill on keeping the secret...there was a sly mention on the 10th anniversary Podcast of how long it had been since Farhan had visited the show, which makes me think the subject of this special project was slowly percolating towards the surface.
I say "Excelsior" to Farhan and Bill !!!
Bill Mc.
N0YUD
I so want to build this. I have a couple of CMOS Si570s left over from building SoftRock RxTx 6.3 and other SDRs. Too bad it won't work since it can only go up to 160MHz. :(
ReplyDeleteHowever, I'm already developing my own DDS front end with a PIC microcontroller. Would be easy to swap it out with one out of the junk box that can connect to the PC with USB. Never had a reason to buy an Arduino yet. With the source code available, I'll probably stick with my own front end to save some money.
Not counting PCB materials, I think I can build one for under $50 (also not counting junk box parts).
What's a good source for inexpensive PCB for RF projects?
Barry
KE4JUC
Having finished up my QSK VFO system for vintage Knight T-50 and Drake 2B (the latter being entirely Bill's fault), the bench is empty and needs a project. A spectrum analyzer to analyze crystal filters has been needed in my shack for a long time. The Arduino has now made this possible with low cost and high accuracy. Wow, Farhan. Obviously, it's time to start planning this next project! Congratulations.
ReplyDelete