Podcasting since 2005! Listen to Latest SolderSmoke

Saturday, April 9, 2016

Soldersmoke Podcast #186 Is Available -- April 1 Rap Up, Pi Talk from Pete, Collins and Raspberries, Bill's Analog RX, Visits and Hamfests, MAILBAG

SolderSmoke podcast #186 is available:


-- April 1 WireWrapRap Rap-up.  Feedback from participants.

-- Bench Reports:
   - Pete talks about his Raspberry Pi SDR DSP rig.  
   - Bill talks about on his Mate for the Mighty Midget Receiver and his R2 Frankenstein.

-- A story from Pete's youth: Cruising the "Miracle Mile" with a Heathkit "Ten-er."

-- Why do we need more RF amplification (in receivers) on 20 than on 40?

-- Have you ever tuned the BFO freq in a superhet by the "sound of the noise?"  

-- A visit to Washington by Jonathan W0OX and family.

-- Bill goes to Winterfest Hamfest with Armand WA1UQO

-- Pete on the importance of balance (in life).

-- Great interviews on QSO Today: Peter Parker, Grayson Evans, and Ashhar Farhan.

-- MAILBAG:
- Paul Darlington M0XPD has a new book about life, travel, and the Dayton Hamvention.
- Michael AA1TJ QRV with a tuning fork at its 2,000th harmonic.
- Jonathan M0JGH living dangerously with homebrew QRP in Italy.
- Ben KC9DLM JoO with MMM
- Stefan DL1DF needs 3.579 MHz rock "with mojo." We have it for you OM.

The music for SolderSmoke 186 was written and performed (the bass lines) by Pete's son Tim.  Thanks Tim!
Pete also suggested that we have some rap lyrics for this music, so renaissance man that he is,  he composed some words. We are still looking for a performer.  

Yo we solder no more – its wire wrap and cables
The cables connect to the small  black box
hold on to your pants and pull up your socks
A cable goes here and a cable goes there
Turn on the switch and its Shazam all software



 





4 comments:

  1. A little Wire-Wrap history: It was a 'transitional' technology, alongside Criossbar telephone exchanges. It was extensively used, replacing soldering, in the termination of the monster mega-pair under-street cables and the phone-numbered excange cables to the exchanges' distribution frames (hard-wired jumpers were manually installed and dis/re-connected btween these numbering schemes here at need - soldering was still used for these as I recall - a labour-intensive and sometimes messily tangled task in a large exchange).
    A Ham Radio snippet: In development and modification of (particularly digital) circuitry, I would have need of jumper wires. One particular task was removing the Opto unobtainium from an OptoPcSCC Card ( I still have it!) for my Packet system. Use of ripped-down Hard- and Floppy-drive cables often served, but tended to be bulky at multiple cross-over points. I found the finer single-cored wrap wire good here, and the insulation better-resistant thermally to multiple re-hash work. There's still a scrap or two lying around in the junk-pile.

    ReplyDelete
  2. I have a pi 2 running a HiQSDR standalone with a 7 inch touchscreen, see original with a Pi 1 model B on QRZ.com (G3VBV).
    The Hermes-Lite also on QRZ.com is now being run with an ODROID-C2 running Ubuntu 16.04 64-bit and a 7 inch touchscreen.

    BTW a W8 contact asked me to wind the HiQSDR down to 1/2 Watt and he could still read me solid.

    ReplyDelete
  3. Steve "Melt Solder" Weber KD1JV designed the ATS-3B BTW

    ReplyDelete
  4. dear Bill,
    I suppose it is time that you (we) need to also talk about mcHF transceiver implemented by Chris m0nka

    ReplyDelete

Designer: Douglas Bowman | Dimodifikasi oleh Abdul Munir Original Posting Rounders 3 Column