Just go to http://soldersmoke.com. On that archive page, just click on the blue hyperlinks and your audio player should play that episode.
http://soldersmoke.com
I am in the process of repairing my beloved 17 meter fishing-pole Moxon. It was taken out of service by the last Nor'easter of the winter. This repair has caused me to review the theory behind antenna directivity. I find there is a lot of "hand waving" in the explanations of how directivity happens: "You put a reflector element next to the antenna. And it REFLECTS!" You are left wondering how that reflection happens. The Royal Canadian Air Force made a video that does a pretty good job of explaining how the reflector reflects. See above. Thanks Canada! While we are talking about antennas, I wanted to alert readers to a really nice antenna modeling program that is available for free. It is called 4nec2. You can find it here: http://www.qsl.net/4nec2/ There is a bit of a learning curve, and I am still climbing it, but I can see how this software would be very useful. It has an optimization feature that runs the antenna through many versions and tells you how to optimize for F/B, gain, SWR, or whatever you want to prioritize. I have discovered that my Moxon was resonant below the 17 meter band. In other words, the antenna elements were too big. About 3.6% too big according to my calculations. This may be the result of my using insulated wire for the antenna elements. Apparently the MOXGEN software assumes the use of uninsulated wire. I'm thinking that an easy way to deal with this would be to use the frequency 3.6% above my target frequency and then use the dimensions given my the MOXGEN program. Any thoughts on this plan? What a shame that Cebik's web sites have all disappeared.
Thanks for that, Bill! I'd already envisaged much of that, but it was good education... Now how do Directors work, particularly multiple at VHF/UHF? SLY beams and the like :) It would also be good to envisage ground effect ... a challenge for the knowledgeable? 73
I have the fiberglass poles, hub, and 14 guage insulated stranded house wiring to build a Moxon and have been slowed a little by the same issue you mentioned. I did find find that the 4nec2 file which defines the antenna shape can be configured to use insulated wire. I haven't modeled it yet, but the following looked useful: https://kk7s.net/2012/07/12/modeling-insulation-and-other-tricks-in-4nec2-4/
"SolderSmoke -- Global Adventures in Wireless Electronics" is now available as an e-book for Amazon's Kindle.
Here's the site:
http://www.amazon.com/dp/B004V9FIVW
Re: ГАГАРИН сказал ПОЕХАЛИ
-
Quote from: Tom W2ILA on April 13, 2024, 09:25:03 AM
He wasn’t the first cosmonaut.
He was the first cosmonaut to land alive.
The Soviet space program owns ...
April 19, 2024. An Audio Amplifier you can Build.
-
I find that data is very useful in making decisions. How startling a
statement to make on a ham radio blog. For instance, when I post subjects
about how t...
No birds do sing
-
Hi FastRadioBurst 23 here letting you know of our forthcoming shows this
week. On Sunday 21st April 2024 at 0900/1300 hrs UTC on 6160 kHz and then
at 2000 ...
An Inline RF Step Attenuator for QRPp Work
-
I don’t need to explain the attraction of low power operation; if you’re
reading this, the chances are that you are already a convert. I’ve been
operating ...
Using an external clock with the RX-888 (Mk2)
-
*The RX-888 (Mk2) and external clocking*
*Figure 1:*
The RX-888 with external clock input *(right)*
The enable/disable switch is barely
visible behind the...
A 51S-1 Restoration Story
-
I came across my Collins 51S-1 in a big junkyard in Ankara, Turkey around
2012. It was in a pile with a lot of other electronic scrap, probably from
one o...
New QRP Cluster Online From OM0ET and OM6APN
-
By DX EXPLORER
DX EXPLORER
Paul OM0ET and Peter OM6APN recently launched a new cluster dedicated to
QRP operations. Have a look and I hope you will enjoy...
3D Printing The Hadley 114mm Newtonian Telescope
-
Yes, we’re building a 3D Printed Newtonian Telescope called Hadley. It’s
being printed in PETG and in the video below, I give a quick tour. My build
isn’...
3D printed project boxes
-
I have been busy with some other things that have kept me away from
electronics projects for quite a while. Now I can get back to them, but
realize I n...
Daylight Again – An all Analog Radio
-
What’s all this? In 10 seconds, A high performance, 7MHz, 5 watt SSB rig
Draws just 24 mA of current 90 dB dynamic range, 80 dB close-in dynamic
range 3D ...
Adding Enclosure to your sBitx Boards Order
-
The early buyers of the sBitx board set who bought it for $270 USD might
want to also add the enclosure (box) for in the kit. What you will now get
is a f...
Digi-chirp! Digital synthesis of ‘nostalgic’ CW
-
The bottom ends of 80, 40 and 20m are not what they used to be. For
starters, the busiest part is the digital segment where computers talk to
computers – l...
-
A Simple Speech Processor
(For QRP/SSB Homebrew Transceivers )
Over the last few weeks I had been thinking to build a small AF speech
processor to add to...
A New Look for your uBitx!
-
Adding a "Cool Blue" Display to your uBitx!
The standard "green background" with black lettering frequently reminds me
that I suffer from Chronic seasickn...
Thanks for that, Bill! I'd already envisaged much of that, but it was good education... Now how do Directors work, particularly multiple at VHF/UHF? SLY beams and the like :) It would also be good to envisage ground effect ... a challenge for the knowledgeable?
ReplyDelete73
I have the fiberglass poles, hub, and 14 guage insulated stranded house wiring to build a Moxon and have been slowed a little by the same issue you mentioned. I did find find that the 4nec2 file which defines the antenna shape can be configured to use insulated wire. I haven't modeled it yet, but the following looked useful:
ReplyDeletehttps://kk7s.net/2012/07/12/modeling-insulation-and-other-tricks-in-4nec2-4/