Podcasting since 2005! Listen to Latest SolderSmoke

Saturday, May 30, 2015

BITX DIGI-TIA Build Update #6: Boxing it up!

 
Basic Basswood Box (From Michael's or Amazon)

 
Space cut out for Si5351 board and for AF Gain and Mic jack

 
Copper flashing placed (from Home Depot)

 
Amplifier Chain placed along the back
 
 
Note Plug-In Low Pass Filter

 
Starting to look Rig-ish

 
The View from Above

 
Still to do:
 
Socketry along the back (Antenna, 12V, external amp T/R control, Speaker, MAYBE:  IF connection).
 
 
Relay wiring (I'm trying to do this with just 2 DPDT relays: one for Low Pass Filter switching and External Amp T/R control,  and one for 12V T/R switching, and Bandpass Filter switching.
 

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Wednesday, May 27, 2015

BITX DIGI-TIA Update #5: Amplifiers Built and Tested


I have the RF amplifier stages done, and I worked a bit on the shielding.  This circuit board will be along the back, turned around, with the copper-clad shields between the amps and the rest of the rig.  In the picture you can see the small inter-stage shields, and one that put between input and output on the final.  All this in the probably vain hope of avoiding the Agony of Oscillation.   We'll see.  So far so good.  I get about 8 watts out of the IRF510 on 40 meters.  53db total gain for the three stages.  Of course, all this will likely change once the rest of the rig, the LP filter and an actual antenna are added.
 
As for the mic amp problems I mentioned last time, well,  I discovered on earlier BITX projects that one of the resistors in the base circuit needs to be changed from 10K to 39K.  It is kind of a long story (maybe for the podcast) but essentially I had to discover this AGAIN.  More details here:
 

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Tuesday, May 26, 2015

BITX DIGI-TIA Update #4


 
Lots of progress over the long weekend.  Along the back you can see the three stages of the RF amplifier chain:  2N3904, 2N2218A, IRF510. I intend to add inter-stage shielding, and one long shield between the chain and the rest of the rig.   Front and center is the Si5351 board (code by LA3PNA).  Mic amp (which gave me a lot of trouble!) is to the right of the Si5351.   AF (RX) amp is to the left (2N3904 and LM386).  The big board in the center has the three Termination Insensitive Amplifiers (thanks Wes and Bob), the 9 MHz filter (thanks Steve Smith!) and the two SBL-1 mixers (thanks to Pete Juliano for the "mil-pad " boards).  And thanks to Farhan for the overall BITX concept and the TIA suggestion.  
 
In the upper right you will see where the plug-in low-pass filter will plug in (a better picture appears below).   I will use a similar plug-in for the band-pass filter.   Combined with the BFO/VFO flexibility of the Si5351, this plug in feature should allow me to cover many bands with this rig.    
 


Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Sunday, May 24, 2015

Sage Advice on Homebrewing from WA3EIB


Bill, Pete,
 
Thanks for the sage advice.
 
You are absolutely right, I should stick to the plan and finish the project before tromping off in a different direction.
Anytime I've ever changed designs before I have completed a task, usually results in something far less than expected.
 
The real joy is completing a project and looking back at what was accomplished.
 
My own personal goals for the Minima Transceiver Construction include...
 
1. Build it from SCRATCH - Manhattan Style.
2. Start with modular construction - so that each circuit can be tested, troubleshot and modified in the future.
3. SMA connectors and coax to every stage so, I can divide and conquer the function of all modules.
4. Document the entire journey so I can actually see where my learning's took me.
5. Provide myself, a basic building block for future transceiver construction and designs.
6. Improve my skills, techniques and knowledge through my mistakes and understandings. 
7. Learn to SLOW DOWN, study, plan and write, in my own words, what the circuit(s) do and how they function.
8. Be a mentor to others and share what I have learned.
9. Be more of an Amateur Radio Experimenter and less of a Ham Radio Operator.
10. Continue to dream and design.
 
Each day should be NEW and EXCITING. There should be a thrill in every step of the way, even in the midst of failures.
 
Thank you both for taking the time to respond.
Thanks for the encouragement and sharing what happens on your own bench.
 
73's
 
Harv -=WA3EIB=-


---------------------

More inspiration from Harv here:
http://soldersmoke.blogspot.com/2012/09/an-ode-to-old-time-radio-by-wa3eib.html

And here:

http://soldersmoke.blogspot.com/search?q=WA3EIB

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Thursday, May 21, 2015

Frank Harris and the Nobel Prize for Sideband

A lot of wisdom and good info in this chapter (and in the whole book);

http://www.qrparci.org/wa0itp/chap15.pdf

http://www.wa0itp.com/crystalsetsssb.html

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Wednesday, May 20, 2015

National RF

 
Pete and I both spotted the ads in QST for this company and their little HF receiver.  In the finest tradition of Tuna Tins and Herring Aids, that receiver is in a SPAM can.   FB. 
 
 
I visited the company's web site this morning.  Lots of great stuff!   They are based in San Diego.  Who are the radio wizards behind this effort? 
  


Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Monday, May 18, 2015

BITX DIGI-TIA Build Update #3 Video of Receiver in Operation



A few things I forgot to mention in the video:

That USB port on the front panel has already come in handy.  I needed to switch the tuning increment from 1 kHz to 100 Hz.   I just went into the Arduino program, removed one zero, and then re-uploaded the code.  

I also put to use the sideband inversion rule-of-thumb:  My IF is at 9 MHz.  I want to receive signals in the 7.2 MHz range, and I want the VFO running ABOVE the IF frequency.  So obviously the VFO will be running at around 16.2 MHz.  So, rule-of-thumb time:  Will I be subtracting the frequency with modulation from the frequency without modulation?  Yes I will!  So, there will be sideband inversion.  This tells me where to position my BFO frequency.   The signals on 40 start out as Lower Sideband.  But as explained above, by the time they get to the filter they will be inverted and will be upper sideband signals.  So I need to put the BFO slightly BELOW the filter passband so that I can tune the signals in such a way as the sidebands fit into the filter passband and have the proper frequency relationship to the BFO to allow for demodulation. I put it at 8.9986 MHz.  With the Si5351, changes to the BFO and VFO frequencies are very easy.

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Sunday, May 17, 2015

Pete Juliano, N6QW, Inducted into the QRP Hall of Fame





Reliable sources in Dayton, Ohio and in the United Kingdom report that Pete Juliano, N6QW, has been inducted into the
QRP Hall of Fame. 
Wow, that's great news! 
Richly deserved! 
Congratulations Pete!

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Saturday, May 16, 2015

SolderSmoke Podcast 176: Knack-Related Conditions: Termination Insensitivity, Sideband Inversion, Dongle Modification, Area 5351 Conspiracy Disorder


SolderSmoke Podcast #176 is available! (And it is GOOD!)

http://soldersmoke.com/soldersmoke176.mp3

16 May 2015

Bench Update:
Pete releases some magic (amplifier) smoke
Pete's new termination-insensitive transceiver makes first contact
Bill goes Yaesu (well, just a filter)
Juliano Mill-Pad boards
Termination Insensitivity is not a personality disorder!
Flip those Bilat Boards!  Pete's cool technique for bilat building
Bill's project notebook and stage testing
Installing the W6JFR EMRFD SBL-1 Bal-Mod Mod

AREA 5351:  Myths, Urban Legends, and Conspiracy Theories about the Si5351

A Rule of Thumb for Sideband Inversion

Dongle Madness and the Dangers of Dongle Modification
What is a dongle?
24 Mhz to 1.7 GHz right out of the box
Modification for 0-29 MHz
Tapping the IF of a Drake 2-B
Getting another one for VHF-UHF
Dongling Meteors, Satellites and Airplanes

SPRAT cover AD9850 in 1988!  Three cheers for SPRAT (and QQ and QST).

Elecraft's new Rig


Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Sunday, May 10, 2015

BITX DIGI-TIA Build Update #2 Installing and Testing Yaesu SSB Filter



Termination Insensitivity.  It sounds like some sort of psychological problem, but it is not!

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Saturday, May 9, 2015

BITX DIGI-TIA Build Update #1 Building the First 2 TIA Amplifiers



I started building the new transceiver today.   I am tentatively calling it the BITX DIGI-TIA.  Digi because it will have at its heart an Si5351 for BFO and VFO signal generation, and TIA because it will use Termination Insensitive Amplifiers (TIAs).  These TIA amps are designed to present a 50 ohm impedance not matter what impedance you connect to the other end.  This is a very useful feature when you are trying to get a certain impedance for a crystal filter in a bidirectional rig -- you want the same termination impedances in  both directions.
 
I built the "top" halves of two of the TIAs, using CNC-cut boards given to me by Pete Juliano.  Thanks Pete!  I like the boards, and I no longer have a thick coating of dried SuperGlue on my fingers.
 
Both amps seem to be performing  very well. Some numbers:
 
Current draw at 12 V (no signal) 30 ma.
 
Gain at 9 MHz (no load):  Amp 1:  27.2 db    Amp 2: 26.5 db.
 
I then took a 110 ohm load and put it across the output of Amp 1.  Gain dropped to 23.9 db (as you'd expect).  BUT HERE'S THE GOOD PART:  The input voltage from my homebrew sig generator stayed exactly the same.    Termination insensitivity. 
 
More on these amps (with a link to Wes's article) here:
 
 
Next  I'll put the 9 MHz filter between these amps and measure the shape of the filter passband.
 


 
Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Thursday, May 7, 2015

IF Selection -- Which Filter for the New Rig?


With some prodding from Pete Juliano, I am moving forward on my next transceiver.  Same wood box enclosure (with copper flashing), but this time I am greatly relaxing some of the radical fundamentalist restrictions:  Chips will be allowed. VFOs and VXOs will be replaced by an Si5351. Filters will not have to be homebrew.  Pete has been putting his CNC machine to use and making me some nice boards with isolation pads already milled in.  Oh, the luxury!

I am going to use the Termination Insensitive Amplifiers designed by Wes Hayward and Bob Kopski back in 2009.  These are especially useful in bilateral type transceivers because they allow you to nail down the termination impedances on the crystal filter IN BOTH DIRECTIONS.   That's is important if you want the same filter shape on both transmit and receive.

But now, with the trauma of my unfortunate IF selection on the BITX 20/40 (now just 20, sniff...) in mind,  what filter should I use on this rig?  The three main candidates appear above.   The 9 MHz Yaesu filter was given to me some time ago by Steve "Snort Rosin" Smith.   The Heath filter (3.395 MHz) and the larger silver one (2.215 MHz) were given to me by Armand Hamel. (Thanks Guys!)

My main band of interest for this rig is 40.   But if possible, I'd like to be able to use it on 15 and 12 meters,  and maybe even 20 and 17,  hopefully without having to change filters. 

 So what say the gurus?  Which one should I use?   Or should I put two of them in there, with provisions that would make it easy for me to move from one to the other? 

Right now my inclination is to go with the 9 MHz filter, perhaps with the 3.395 MHz filter also available.


Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20
Designer: Douglas Bowman | Dimodifikasi oleh Abdul Munir Original Posting Rounders 3 Column