Dover update: Falling from tree, B2 inheritance?, HB variometer

That's me (the new boy in the workshop) at the key of Ian G3ROO's B2 spy set. Beautiful rig. You will all, I'm sure, understand Nigel M0NDE's question to Ian (see below). The Dover variometer project is very interesting (picture at the bottom). Thanks Nigel! (Try to keep Ian at ground level, OK?)

Hi Bill, a Dover construction club update:

Ian was cutting down some trees in the garden this weekend, and took a tumble. As he fell I asked him if I could be left the B2, I can't tell you exactly what he said but you can imagine. Fortunately he was not injured as the ground was soft with all the rain we have had. The B2 remains in the museum for now.

The black hole has taken the variometer from us forever so a new one was made Thursday night at club. You got the blame tonight for anything that was not in its proper place when sought, the new boy in the workshop always takes the blame!

A length of plastic drain pipe was selected. A coil of about ten turns was wound around a large capacitor as a former and tied off with beeswaxed rafia then mounted onto a plastic rod. The plastic rod had a hacksaw slot put in it lengthwise to facilitate the copper wire exiting the plastic pipe. The plastic pipe was drilled and squeezed and the coil inserted into the pipe. The rod was held in place by friction fit brass washers. Two coils were wound around the plastic pipe,in similar directions. The wire is just tensioned by being passed though holes and threaded in and out of the pipe at each end. A plastic screw allows the inner coil to move through just 180 degrees. The first test showed two inductance ranges were possible 6-12 micro Henries and 12 to 21 mH. We will add additional coils up the pipe to give 21 to 30, 30 to 40 etc. A ten meter fishing rod will form the vertical element, with this variometer and switched coils providing the tuning. The experiment continues next Thursday night.

73 de Nigel Evans M0NDE QTH Dover

Black Holes in Workshops?

Nigel (M0NDE), Ian (G3ROO), Tony (G4WIF) at Dover CC HQ

When I was out in Dover (UK) last week the fellows in the Dover Construction Club alerted me to a problem that has been affecting their workshop, and that may be causing trouble in yours: black holes. Apparently through some strange quirk of quantum physics, small black holes are sometimes generated in electronics workshops. They cause parts and tools to disappear. The quantum element of all this is readily apparent: only those parts and tools that you REALLY need disappear. If you don't need a particular part or tool, it will not be affected. The guys out in Dover recently lost a variometer this way, and while I was there a telegraph key briefly disappeared into the quantum mist. In a variation of this phenomenon, very small black holes sometimes pop out of the quantum vacuum when small parts are dropped to the floor -- that's why you often can't find them! SMT parts are especially susceptible to this (obviously because some of the damn things are getting down to quantum scale) . I don't really know what can be done to counteract this problem -- if you have any suggestions, please post a comment.

On a related subject, Jim Miller sent us this:

Tools Explained DRILL PRESS : A tall upright machine useful for suddenly snatching flat metal bar stock out of your hands so that it smacks you in the chest and flings your beer across the room, denting the freshly-painted project which you had carefully set in the corner where nothing could get to it. WIRE WHEEL : Cleans paint off bolts and then throws them somewhere under the workbench with the speed of light. Also removes fingerprints and hard-earned calluses from fingers in about the time it takes you to say, "Oh, shit!" SKILL SAW : A portable cutting tool used to make studs too short. PLIERS : Used to round off bolt heads. Sometimes used in the creation of blood-blisters. BELT SANDER : An electric sanding tool commonly used to convert minor touch-up jobs into major refinishing jobs. HACKSAW : One of a family of cutting tools built on the Ouija board principle. It transforms human energy into a crooked, unpredictable motion, and the more you attempt to influence its course, the more dismal your future becomes. VISE-GRIPS : Generally used after pliers to completely round off bolt heads. If nothing else is available, they can also be used to transfer intense welding heat to the palm of your hand. OXYACETYLENE TORCH : Used almost entirely for lighting various flammable objects in your shop on fire. Also handy for igniting the grease inside the wheel hub out of which you want to remove a bearing race. TABLE SAW : A large stationary power tool commonly used to launch wood projectiles for testing wall integrity. HYDRAULIC FLOOR JACK : Used for lowering an automobile to the ground after you have installed your new brake shoes, trapping the jack handle firmly under the bumper. BAND SAW : A large stationary power saw primarily used by most shops to cut good aluminum sheet into smaller pieces that more easily fit into the trash can after you cut on the inside of the line instead of the outside edge. TWO-TON ENGINE HOIST : A tool for testing the maximum tensile strength of everything you forgot to disconnect. PHILLIPS SCREWDRIVER : Normally used to stab the vacuum seals under lids or for opening old-style paper-and-tin oil cans and splashing oil on your shirt; but can also be used, as the name implies, to strip out Phillips screw heads. STRAIGHT SCREWDRIVER : A tool for opening paint cans. Sometimes used to convert common slotted screws into non-removable screws and butchering your palms. PRY BAR : A tool used to crumple the metal surrounding that clip or bracket you needed to remove in order to replace a 50 cent part. HOSE CUTTER : A tool used to make hoses too short. HAMMER : Originally employed as a weapon of war, the hammer nowadays is used as a kind of divining rod to locate the most expensive parts adjacent to the object we are trying to hit. UTILITY KNIFE : Used to open and slice through the contents of cardboard cartons delivered to your front door; works particularly well on contents such as seats, vinyl records, liquids in plastic bottles, collector magazines, refund checks, and rubber or plastic parts. Especially useful for slicing work clothes, but only while in use. Son of a bitch TOOL : Any handy tool that you grab and throw across the garage while yelling, "Son of a bitch" at the top of your lungs. It is also, most often, the next tool that you will need. No trees were killed in the sending of this message. However, a large number of electrons were terribly inconvenienced

SolderSmoke Podcast #122

Bill (N2CQR) and Ian (G3ROO) in Dover, England (with hydrogen balloon spark key)

SolderSmoke!
A SHOW FOR ELECTRONICS HOMEBREWERS!
Listen at: http://www.soldersmoke.com
SolderSmoke #122

Feb 28, 2010
Snow in Rome!
In London: A visit to Marconi's house, Maplins, and Faraday's lab
A visit to the Dover Construction Club
Computer problems resolved
A short period of QRSS, then back to WSPR
Putting the Drake 2-B into WSPR mode
The Rome-Norway WSPR pipeline
Increased solar activity
50 years of SETI with Frank Drake
QQ Review
Work Bench Eye Candy
Movie Review: UP! (Five Soldering Irons)
MAILBAG

The Dover Construction Club

Last night there was a meeting of the Dover Construction Club (discussed by Nigel, M0NDE, in Solder Smoke #194). For the first time, the members agreed to be photographed.

Above, in the foreground, Merv checks the main board of his softrock, Ian explains to Paul how a mod to an old FT101ZD will work, and Nigel is seen using the microscope and observe to Merv he has not soldered all the IC legs down on a SMD board. He says he knows. grin!!

Ian Keyser, G3ROO, host of Dover Construction Club. At his bench in a separate part of the workshop where he has test equipment to diagnose the inevitable faults. Here he is working on the RAMU featured in a past edition of Sprat.

In a corner of the garden a brick arch leads to the workshop door, behind the brown door hides the secret world of the amateur radio constructor. Obviously, this is something of a clandestine operation.

Tony, sitting at the other end of Ian's test area, taking down some CW.

In this workshop club members have bandsaw, milling machine, lathe, and pillar drill.

Wow! That's the kind of club that we'd all like to be part of -- Nigel's comments on SS 104 generated a lot of envious e-mail . Thanks a lot guys!