Just go to http://soldersmoke.com. On that archive page, just click on the blue hyperlinks and your audio player should play that episode.
http://soldersmoke.com
I don't know why, but this weekend I got the urge to get on the air with a very low power homebrew QRP rig. I reached for my Tuna Tin 2 -- Herring Aid 5 combo. I call it the Fish Soup 7 (seven transistors in total). I first tried to turn this rig into a transceiver by taking the VFO signal from the receiver (it is direct conversion) and using it to excite the Tuna Tin 2, but it just didn't work out. The oscillator in the Herring Air 5 is very bare bones -- no buffering and an LC circuit that is mostly L (10 uH). It became very difficult to get a stable amount of CW offset. So I went back to crystal control for the transmitter. I did replace the 5K tuning pot in the RX with a 10k 10 turn pot (thanks to W8NSA). Tuning is now very smooth. I used my old UK freq counter to monitor my receive freq. (Thanks to Tony Fishpool G4WIF-- back in 2009 he sent me the CMOS chip that brought this counter back to life.) I was putting out about 750 milliwatts. I had a very quick contest-like contact with K2D -- one of the "13 Colony" stations. Then a longer chat with Hank K1PUG (see video above). I had lost my 7050 crystal, but this morning it re-appeared. TRGHS. As you can see in the video I am using the beautiful VU3XVR key that Farhan brought me from India. This was fun. I may try to put a VFO of some sort into the TT2, just to get more agility. But I want to keep things simple. Look for me on 7050.
"SolderSmoke -- Global Adventures in Wireless Electronics" is now available as an e-book for Amazon's Kindle.
Here's the site:
http://www.amazon.com/dp/B004V9FIVW
Power standing wave null… more
-
Power standing wave null? discussed the “Power Standing Wave” concept
unfolding on social media. Already a correspondent has asked if the graphs
given in P...
Vintage 6 & 2 AM - Gonset & WRL/Globe
-
Just in time for the season:
1) Globe Hi- Bander 6 & 2 AM. 65 watts input on 6 & 50 watts on 2.
This transmitter is in good condition physically but is unte...
April 25, 2024. Meter Magic
-
At times we need to include some form of metering in our homebrew rigs. No,
we will not be installing a Nano VNA in a transmitter. But often a current
mete...
Trying a $15 70cm transceiver HK-188
-
Peter, VK3YE, recently posted a video of a pair of 433Mhz transceivers he
bought at Aldi for $20. They worked OK but had a number of obvious annoying
probl...
An Inline RF Step Attenuator for QRPp Work
-
I don’t need to explain the attraction of low power operation; if you’re
reading this, the chances are that you are already a convert. I’ve been
operating ...
Using an external clock with the RX-888 (Mk2)
-
*The RX-888 (Mk2) and external clocking*
*Figure 1:*
The RX-888 with external clock input *(right)*
The enable/disable switch is barely
visible behind the...
A 51S-1 Restoration Story
-
I came across my Collins 51S-1 in a big junkyard in Ankara, Turkey around
2012. It was in a pile with a lot of other electronic scrap, probably from
one o...
New QRP Cluster Online From OM0ET and OM6APN
-
By DX EXPLORER
DX EXPLORER
Paul OM0ET and Peter OM6APN recently launched a new cluster dedicated to
QRP operations. Have a look and I hope you will enjoy...
3D Printing The Hadley 114mm Newtonian Telescope
-
Yes, we’re building a 3D Printed Newtonian Telescope called Hadley. It’s
being printed in PETG and in the video below, I give a quick tour. My build
isn’...
3D printed project boxes
-
I have been busy with some other things that have kept me away from
electronics projects for quite a while. Now I can get back to them, but
realize I n...
Daylight Again – An all Analog Radio
-
What’s all this? In 10 seconds, A high performance, 7MHz, 5 watt SSB rig
Draws just 24 mA of current 90 dB dynamic range, 80 dB close-in dynamic
range 3D ...
Adding Enclosure to your sBitx Boards Order
-
The early buyers of the sBitx board set who bought it for $270 USD might
want to also add the enclosure (box) for in the kit. What you will now get
is a f...
Digi-chirp! Digital synthesis of ‘nostalgic’ CW
-
The bottom ends of 80, 40 and 20m are not what they used to be. For
starters, the busiest part is the digital segment where computers talk to
computers – l...
-
A Simple Speech Processor
(For QRP/SSB Homebrew Transceivers )
Over the last few weeks I had been thinking to build a small AF speech
processor to add to...
A New Look for your uBitx!
-
Adding a "Cool Blue" Display to your uBitx!
The standard "green background" with black lettering frequently reminds me
that I suffer from Chronic seasickn...
This comment has been removed by the author.
ReplyDeleteNow that is how its done!! Manual T/R switch and all!!
ReplyDeleteLove it!
Pete
KD2OMV
Bravo Bill!! Way to go!! 750 milliwatts, and no amp, WOW!!!
ReplyDeleteEd KC8SBV