Podcasting since 2005! Listen to Latest SolderSmoke

Monday, October 8, 2012

Harv's Hallicrafters HT-37: A Thing of Beauty


Good Evening Bill,

Well with sore fingers, I’m glad to report that the upper deck of my newly acquired HT-37 is complete. (see enclosed photos)
Mice had a small party in this radio but aside from the numerous corrosion spots and few frayed wires,  the task of restoring was not too over whelming.
I have had my trusty Soldering Iron in high use mode lately.
All but the final tubes have the Hallicrafters logo stamped on them.
I had to replaced the Final Tune Capacitor C55 and have gone through all the modifications done to this radio during its 52 years of service.
The previous owner added an internal Antenna Relay (grey transformer near rear of deck.) and replaced the Mic connector with a Drake style phono jack. (I guess that’s acceptable.)

Now I’m onto the re-capping of the lower deck, De-ox the tube sockets and switches. Finally, the replacement of the rectifiers with solid state devices.
I’m documenting all the details just in case there is another solder melting soul out there that wants to restore their HT-37.
With some tender care, it should last another 50 years.

Bill, Keep on learning, Keep on burning (solder that is!)

73’s & Enjoy

Harv -=WA3EIB=-


Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Sunday, October 7, 2012

My Mate for the Mighty Midget


Al, W1UX, asked for a picture of the receiver that I used to listen to his dulcet tones this morning.   Here you go Al.    Here is an article on the project: 

http://www.gadgeteer.us/erart.htm


Above is the Mighty Midget RX paired up with a DX-60 and a VF-1 (circa 1998)


Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

W1UX


Now THAT'S a ham shack! My Mighty Midget receiver allowed me to listen in this morning to Al, W1UX, and friends on 75 meter SSB. One of Al's AM operating positions appears above.  Note the DX-100.  And the R-390 (want one).  And the Tek 465. I've been a big fan for years.  Check out Al's boatanchor web site:    http://www.tinyradio.com/boatanchor01.html  

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Saturday, October 6, 2012

Mighty Midget RX on a Key Chain


The key chain device will soon be carried to 1200 feet by our new rocket.



Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Friday, October 5, 2012

Sputnik Party 2012 Soapbox

Poster by Steve "Snort Rosin" Smith

3 October from AA1TJ:

Here's an admittedly late reminder that the Sputnik Party begins

tomorrow (4 October). I've been preoccupied with non-hobby concerns in
recent months but I did manage to throw something together for the
event.

My transmitter follows the lines of the 10mW, battery-powered, RF
beacon that was carried into orbit in 1958 by "Vanguard 1." You may
recall this is the one Premier Nikita Khrushchev characterized as "the
grapefruit satellite."

My present build uses essentially the same circuitry and componentry
as did an earlier, 20m version; details of which can be found at

http://aa1tj.blogspot.com/2012/06/vanguard-1-satellite-transmitter.html

The 15m version drives a 44m end-fed wire with 30milliWatts.

The receiver that I built for the event is essentially a "Q-multiplier
-> detector" type regenerative job. However, the Q-multiplication is
accomplished by a parametric amplification using a quartz-crystal
controlled pump. I thought it would be historically appropriate given
that parametric amplifiers were all the rage in the late 1950's.

I put together the keying and R/T changeover circuitry this morning.
When it appeared that "all systems were go" I began sending CQs on
21.060MHz. The band, or at least that portion of the band (the
receiver only tunes from 21.060 to 21.064MHz), seemed rather quiet,
but my 6th call netted a "dit dit dah dah dit dit." Resending my call,
I was very pleased to hear HB9DCL come back to me from just outside of
Zurich. The reports were 579/339. Frank was running 5W to a log
periodic antenna. I sure hope this is a sign of things to come!

I hope to be at the key by 1300Z tomorrow. Although my little
"grapefruit" only puts out 30mW, folks running "Sputniks" made from
ex-Soviet subminiature "rod tubes" should be at least two S-units
stronger. A number of European stations will be operating this year
and at least one station that I know of will be QRV from Japan. Just
listen for the beeps and give them a call!

Thank you,
Mike, AA1TJ

.......................


04/10/12  ( first day)
dear friends &Sputnikers
today a Belgian "sputnik clone" crossed the pond
first hit
15:22 with N0UR a 2 x sputnik "solid" QSO
Jim wrote: Thanks QSO, here is how you sounded in MN
( in attach)
16:00 second hit with AA1TJ , Mike "the inventor of all this Sputnik madness" hix 3 
this time a bit more difficult but at last we could manage to exchange reports,
between the QRM and noise at last got confirmation , 
Mike's sigs  here where 339 but still copyable
all OK with my 559 sigs then suddenly some other sputnikers came on the scene and I lost Mike
nevertheless
with my 60 years again excited as a young boy
as we made some history today hi x 3
will take a picture
for the moment a complete mess as the DC/DC invertor inside the sputnik  broke down
lost the very early contact with UA1CEG suddenly no more power in the SPUTNIK-cabine LOL
had to drag my new testbench power supply (still under construction )
or  lot of things to fix for those lausy 700 milliwatts hahahaha
73 to all
Jos
ON6WJ

.................................

News flash...Sputnik worked Vanguard across the pond. I just sent this
letter to some of the guys

Dear Friends

I won't forget this morning's QSO with ON6WJ anytime soon! As he
beeped/called CQ I could hear him riding on waves of QSB. I kept
hoping he would end on the top of the wave. It happened one time and
Jos sent "AA1TJ?" but by the time I re-sent my call we were back in
the trough of the wave. He started calling again and once again I
crossed my fingers. Finally it happened, he ended on top of a
particularly strong peak...and sure enough, he copied my callsign. It
took more effort to exchange the reports but we eventually did it! He
confirmed my 559 and I did the same for my 339 report. It must be true
that anything worthwhile doesn't come easy, because the more difficult
the QSO the more I seem to enjoy it! I copied Jos' info: "SPUTNIK PWR
700mW = ANT 3EL YAGI" perfectly on my tiny receiver. Just as amazing,
he copied my 30mW transmitter made from one PNP Germanium transistor
dating from September of 1959. Needless to say, I'm a happy camper
today. Merci Beaucoup, Jos.

Just above my operating frequency I heard PA0PJE sending "CQ Sputnik."
You had a beautiful signal here, PJ! It was easily S6 on the peaks. My
transmitter frequency trimmer adjustment is buried in a rat's nest of
wires which I didn't dare stick my hand in so early in the day.
However, if I hear you again I will definitely risk it.

Thanks Carlo/IZ4KBS and congratulations on your Russian QSO. Any
contact all with this simple stuff is reason for a celebration!

...and now back to the Hobbit Hole for another dose of QRPp.

73/72,
Mike, AA1TJ



Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Tuesday, October 2, 2012

Ham Radio Exam Day in Ireland: October 4

OK gang, it is time for us to do what we can to help a worthy Short Wave Listener transition into the world of amateur radio.  Chris will be facing the Irish radio examiners on October 4.  So please try to send some positive vibes in the direction of Ireland.  Cross your fingers (especially the ones with the soldering iron scars!)  Maybe melt some sacrificial solder. C.F. Rockey might suggest sacrificing a chicken to Papa Legba.   Say a prayer if you are so inclined.   Good luck Chris!  

Hi Bill,

Just wanted to say thanks for the great podcast and keep up the good work.

I’ve been listening for a good while now and following your subscriptions advice on things like Tim’s “Hot Iron” Constructors club and QRP/Sprat magazine.

I’ve got my Amateur Radio licence test in 2 days time (4th Oct) over here in Ireland (Dublin’s Comreg Offices) so please give all the candidates a mention and wish us luck.

Great book as well…  When I’ve had my fill of studying I switch over to your book for a while to relax a bit and read your thoughts on getting to grips with it all.

There’s only one licence here in Ireland so it’s Full or nothing  so it’s going to be tough! My brain is well and truly fried!!

I’m determined not to be a (can’t even remember what you call them in your book ha ha) “User” and go out and buy everything I need so I’m looking forward to lots of construction projects when (IF!) I get my licence J

Best Regards (I don’t think I’ve earned my right to use 73’s yet),

Chris
(EI1628 SWL/qrz.com)


Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

How to Get Ready to Build a BITX-20




Continuing with our workshop inspiration theme, I spotted this in the BITX-20 mailing list this morning.  The response is from Farhan: 

blake,

i would suggest a different route. a long and winding one, that will
finally lead to a bitx.

the idea is to learn. you do this by understanding what you build and
building what you understand. by 'understand', i specifically mean, being
able to measure. here is what i suggest, buy yourself a bunch of 2N3904s
from the local radio shack and some resistors and caps. then build this :

http://www.phonestack.com/farhan/testosc.gif

this is an oscillator. if you plug a coil between the open ends, it will
become a vfo, if u plug a crystal, it becomes a crystal oscillator. you can
use your frequency oscillator to check the frequency it is oscillating at,
etc.

with this, you would have mastered the first of the three blocks that make
up almost every radio circuit. but next, you must make another test
instrument. a power meter. most of us ham start out with a simple RF probe.
while that was fine and dandy for its day, now we can do much much better.
we can make a very accurate power meter that enable you to measure things
as finely as anybody in this business. W7ZOI has designed a super simple
power meter. it is available as a kit.
read about the power meter here :
http://www.kangaus.com/Documentation%20files/Power%20Meter%20Documentation%20May%202011.pdf
you can purchase the kit at www.kangaus.com
(I have no business interest with kanga or any other kit manufacturer)

with the power meter in place, you can now measure the power levels coming
out of any circuit with great accuracy.

now, you can build a single stage feedback amplifer (there are six of them
used in the bitx) on a copper clad board. using the test oscillator as an
input, you can measure how much gain the amplifer has (measure the
oscillator output, then connect the oscillator to the amp and ,measure the
amp output. the, amp output - oscillator output = amp gain).

of course, while building both these blocks, you will discover what
voltages to expect at which junction of components in both these blocks.

next, you can build a step attenuator. which is a really simple thing and
of immense value in the home lab. here is a design
http://www.arrl.org/files/file/Technology/tis/info/pdf/9506033.pdf
or you can now buy it in a kit form from
http://www.qrpkits.com/attenuator.html

finally, you can build a simple signal generator like this :
http://www.phonestack.com/farhan/siggen.html  . this will allow you change
frequencies and measure what a circuit does at different frequencies. you
can use this to test how the filters are doing and get them to 'spot' where
you want them to.

so, there it is, a signal generator, a power meter, step attenuator, test
oscillator. four, very simple test instruments that you  can build
yourself. they will give you one helluva education in radio. and within
weeks, you will understand and start building on your own!!

- farhan


> Quoting bfabman :
>
> Hello Everyone, I have been watching the group for a few months now
> with interest. I have no electronic experience to speak of, but I have
> a burning desire to make one of these, and I am wondering what all of
> you think of someone like myself building one as my first real radio
> project, to be used for qrp mountain topping. I don't have any
> electronic test equipment for the final alignment, other than a
> standard DIG vom meter. (I am willing to buy some equipment if
> necessary) I think that this would be an awesome winter project just
> don't know if it would be over my head. If I got it all built, could I
> actually get it aligned and working properly. I did make a Norcal
> frequency counter project last year and it turned out very well. Thanks
> for your opinions before I spend the money. Blake
>
> Paul Daulton K5WMS
> beacon WMS 185.302 khz qrss30/slow 24/7
> Jacksonville,Ar 72076
> em34wu

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Sunday, September 30, 2012

Science Fair Light Beam Communications in 1960s


Hi Bill!  This Bob Schubert, KC4FNE in Blacksburg Virginia just wanting to say hello and taking the opportunity to say "Thanks" for the SolderSmoke Series.  I have to let you know your podcast accompanies me as I do my early morning exercise regime.  Before SolderSmoke, I would begrudgingly get out on the track every other day.  Now I'm out there just about every morning listening to a new episode.  I'm not sure what I will do once I exhaust all of the episodes?  Normally I would cover my obligatory 2 miles in 45 minutes, now I'm looking for excuses to stay on the track so as to complete a one-hour or so episode.  When I'm listening to it in the car, I find myself circling the block just so I can finish a podcast.  It has also prompted me to purchase the SolderSmoke book.  I'm thoroughly enjoying the book as we seemed to have both grown up close to the same timeframe and our early lives led as "geeks."  If you interetsted in what an "old geek" is up to now, point your browser to http://www.lumenhaus.com/  This is a solar powered house done by a team of architecture and engineering students/faculty I was involved with.  If you ever find your way to Blacksburg and are interetsed in our Lumenhaus, I would be happy to provide a tour.

I've included a photograph of me taken at Orange County High School in the mid-60's with a science fair experiment "Talking on a Light Beam." While not quite in the 478THz range of the high-power LEDs it was up there!  While modulating the filament on a flashlight I would be hard-pressed to go 95ft much less 95 miles.

Best, Bob Schubert KC4FNE


Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Saturday, September 29, 2012

Video Model Rocketry


Our plan is to strap a key-chain video camera to the center of gravity on this mean green machine.  Using Duct Tape (of course).  Kind of like this guy did:  

http://www.teamten.com/lawrence/projects/video-camera-on-model-rocket/


Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Friday, September 28, 2012

Bell Labs: Similarities in Wave Behavior



John N. Shive rocks the universe with his 1959 wave machine.  We saw this device some time ago in a video in which Dr. Shive explained standing waves.  Thanks to Armand WA1UQO for alerting us to this gem.  

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Wednesday, September 26, 2012

SSB Generation: Ideas from Around the World


I liked this thread on the EMRFD mailing list.  The question of how best to generate SSB is very interesting, and I also liked the global scope of the Q&A:  Peter in Hungary asks the question, Farhan in India and Allison in the U.S. respond.   

 On 9/25/12, ha5rxz wrote:
When generating an SSB signal from audio and a 9 MHz carrier which would be
the best mixer to use?
a) A high-level ring bridge mixer such as the SRA-1H
b) An H-Mode mixer using an FST3125 chip
c) An H-Mode mixer using a 74HC4016
d) Something else
Note that this mixer will not be used to demodulate.
Peter HA5RXZ

...................................
Ashhar Farhan wrote:
In my experience, if you keep the audio level low enough, it is
difficult to beat a simple two diode mixer.with a 10 db attenuator in
the output. Having just two diodes makes balancing of reactive as well
as resistive differences of the two diodes quite trivial. Schottky
diodes are best.
One thing, I did discover though is that the balance should be to
minimize the harmonic distortion, rather than just the carrier
suppression.
What we are shooting for is to keep the In-band IMD down. Carrier
suppression is just hygiene. So, you will want to tune in to the
signal, modulating it with two tones and see it on a audio spectrum
analyzer (freely downloadable from the net) and try getting the third
spike down.
Though the 'packaged' mixers don't give you the needed control for
hi-fidelity, for trivial usage, NE602 is pretty good. Just drop it
into the rig and live with what you get (which is not bad at all).
The best resource is the chapter on phasing receivers and transmitters
in emrfd. Rick is the guru. I hope he joins this thread.
 
- Farhan

............................................
FROM KB1GMX: 

I'll weigh in..

Yes, they all work. You need a provision for adjusting carrier balance on some but anything over 40db will be good.

I've used 602/612s, SBL-1, SBL-1H, diode rings, and even varicap
diodes (there is a design using them in capacitively balanced 
a modulator from many years ago. They all work if the levels are correct.

These days I use the sa612 for simple designs, SBL-1 with a 50ohm 
pot added for balance for better radios and the 4 diode ring I've 
used many times as its uncritical, needs only one untapped 
transformer and easy to make. Most of those are listed in the 
older 1975 through current handbooks and EMDRFD.

If needed I can post to the files section a few designs but 
they are all textbook and all are capable of good results.
In just about all the diode modulator cases a fairly strong 
carrier (5mW or more) is needed and the audio will be about 
10db lower for very good result. The active devices like the
ca3028(and friends), SA612, MC1496 the levels for the carrier 
and audio must be matched accordingly for the device. You can 
look at the output with a scope and get a first order eyeball 
call on quality (no carrier and no clipping or limiting) and a
receiver (any your ears) will tell you if its right.

Allison


Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20
Designer: Douglas Bowman | Dimodifikasi oleh Abdul Munir Original Posting Rounders 3 Column