Some unbridled Australian enthusiasm... (Two Videos from Oz)

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics"http://soldersmoke.com/book.htmOur coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmokeOur Book Store: http://astore.amazon.com/contracross-20

JBOT Installed in Azores 17 Meter SSB Rig

Even though one of their Coronal Mass Ejections is due to hit us soon, the radio gods have been quite kind to me this morning. I installed the JBOT amplifier board in the 17 meter SSB transmitter that I had built out in the Azores during the last solar cycle. The board went in without any trouble. And I was a very surprised when it DIDN'T break into oscillation and instability! Holy Cow! This one was stable from the start! Even when connected to my antenna! Eureka!

The rig still needs some peaking and tweaking. I'm only getting about 2-3 watts out and I should be getting 4-5. I did a quick and dirty "by ear" alignment --- I just listened to my own signal with my trusty Drake 2-B and moved the carrier oscillator freq around a bit until the SSB audio sounded good (you never have to do that with DSB!).

For those of you not familiar with this rig, here is some background:
-- Built on the chassis of an old Heath DX-40
-- Crystal filter at 5.174 MHz. Filter rocks and carrier oscillator rocks from an old Swan 240 I picked up in the Dominican Republic from Pericles Perdomo HI8P (SK).
-- Based on a design published in SPRAT by Frank Lee, G3YCC (SK).
--Heterodyne oscillator is a G3RJV Universal VXO circuit running at around 23.3 MHz.
-- That orange cord to the big meter that you are no doubt wondering about is just a little circuit that monitors total current drawn by the rig. It bounces up and down as I talk. I put it in there mostly because I wanted to make use of a beautiful old Simpson meter that I picked up in 1973 at the Crystal Radio Club (W2DMC) in Valley Cottage, New York.

Going around, clockwise from below the meter: G3RJV VXO, carrier oscillator and two diode balanced modulator board, crystal filter (with NE602 mixer and post-filter bandpass filter to the left), JBOT PA. Audio amp (using op amp) below the chassis. T/R relay in the center (antenna changeover relay below the chassis).

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics"http://soldersmoke.com/book.htmOur coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmokeOur Book Store: http://astore.amazon.com/contracross-20

The Father of the CK722 (and RadioShack!)

Steve Smith of SolderSmoke's West Coast bureau sent us the link to this article about a very interesting guy who made enormous contributions to the radio art. Three cheers for Norman Krim!
http://tinyurl.com/7qsdq22

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics"http://soldersmoke.com/book.htmOur coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmokeOur Book Store: http://astore.amazon.com/contracross-20

DIY at the V&A (Victoria and Albert Museum)

http://blog.makezine.com/2012/01/17/the-power-of-making-at-the-va/

Power of Making from Juriaan Booij on Vimeo.

One of the many perks that I enjoyed during my four years in London was living near that city's amazing museums. I was more of a Science Museum or Natural History Museum guy, but the we also loved the V&A. Each day on my way to work, the 414 bus took me past the V&A's magnificent facade. I always tried to get a seat that would allow me to get a good look.
The Maker Blog reports that the Victoria and Albert recently had an exposition on people who make things in their own private workshops. We are not alone! The video imbeded above is some sights and sounds from the world of DIY. The link below takes you to another video that includes some nice interviews with folks who are making things.

http://blog.makezine.com/2012/01/17/the-power-of-making-at-the-va/

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics"http://soldersmoke.com/book.htmOur coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmokeOur Book Store: http://astore.amazon.com/contracross-20

Another JBOT Amplifier

Over the weekend I built another JBOT 5 watt linear amplifier (design by Farhan). I used a nice piece of copper-clad board that Dave, W8NF, sent me (thanks again Dave).

This time I chickened out regarding the possible conductivity of the anodized heat sinks. I didn't have any trouble with this on my first JBOT, but I worried that if the anodized layer gets flaked away, a heat sink might short one of those collectors to ground. To be on the safe side, I put small squares of Gorilla Tape on under the heat sinks. (PLEASE don't tell me that Gorilla Tape is conductive!)

For T1 and T2 I used FT50-43 toroids instead of the TV baluns used by Farhan. He had recommended FT37-43's as an alternative to the TV baluns, but I went with the slightly larger toroids. For T3 I rolled my own binocular core using four FT37-43 toroids stacked 2X2.

The amplifier has passed the smoke test. Next I have to put in the low pass filter (Steve Smith: Please note that I have left space on the board for the filter.) Then this version will face its real test when it goes into the 17 meter Azores SINGLE sideband rig.

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics"http://soldersmoke.com/book.htmOur coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmokeOur Book Store: http://astore.amazon.com/contracross-20

Sunspots: As Good As It's Going to Get

The good news is that conditions are not a lot better than they have been. The bad news is that they won't be getting much better. But take heart guys: the next few years should be pretty good. Now is the time to get those rigs and antennas for the upper HF bands in shape. Construction of a second 17 meter JBOT amplifier begins today (this one for the Azores SSB transmitter).

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics"http://soldersmoke.com/book.htmOur coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmokeOur Book Store: http://astore.amazon.com/contracross-20

Warning! QRPers May Find This Disturbing!

Greg, KC2DWF, sent me this link to a really great web site about the AM broadcast station WLW (aka "The Nation's Station"). Brace yourselves guys, for we are now moving out of QRP land: The exciter on this baby is 50 kilowatts! The modulator could produce 400 kilowatts of AUDIO! The article is very well written, obviously done by an aficionado of high power RF. There are some great lines in there. Here is a sample:

This brings up the real fun part of 1934 AM broadcasting - NO LIMITERS! WLW, like any big-time station at the time, gave the Full Monty: 100 per cent modulation. Now, radio textbooks always have cute little pictures of sine waves at 100%, but people don't talk in sine waves. They don't beat drums, play hillbilly music, or yodel in sine waves. If the studio asked the big rig for some outrageously asymmetrical upward modulation barely crossing zero at all, the DC-sucking beast said FEED ME and obliged - briefly. Voltmeters dipped at the power company, antenna current went haywire, cows felt funny tingles in odd places, and various shotgun-loud bangs and sparks filled the transmitter building.

Have fun, but don't get any QRO ideas...

Here's the link to the article:
http://www.ominous-valve.com/wlw.html

More info and pictures here:
http://www.oldradio.com/archives/stations/cinc/wlwpix.htm

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics"http://soldersmoke.com/book.htmOur coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmokeOur Book Store: http://astore.amazon.com/contracross-20