Ambition, Greed, and Experiments with a Divide by 2 IQ VFO

Fresh from a great success with the use of the M0XPD divide by 4 I and Q VFO in my Frankenstein Phasing Receiver, I got ambitious.  And greedy.  I wanted more.  More frequency coverage.  More bands.  Divide by 4 can really limit your frequency range.  The AD9850 only goes up to 40 MHz.  Divide by 4 and you can't even get the 30 meter band. 

So I started looking at other options.  Si570 looked nice, but here the lower limit was the problem: 10 MHz.   Even with divide by 4,  that knocks out 160 meters, a band I am very interested in lately, and that seems to sound especially good in a direct conversion receiver.

Once again, the controversial Si5351 was calling my name.  It would go down to 8 kHz and up to 160 Mhz.  Woo Hoo!  If I could build a divide by 2 IQ VFO, I could cover 160-6 meters.   

Here is the basic idea.  From:
http://www.markimicrowave.com/blog/2015/04/top-7-ways-to-create-a-quadrature-90-phase-shift/

 The Flip Flops are set up to change state when the input signal is going up.   By putting an inverter at the input of the bottom FF input, in effect you have that one changing state when the input signal is going down.  Look at this for a minute or so.  Look at the square waves at the bottom.  See it?  See how it takes an ordinary signal and spits out two signals, one 90 degrees off the other?  Pretty cool, don't you think?

With lots of hardware help from Todd VE7BPO, and software help from Tom AK2B (wizards both), I got my Si5351 divide by 2 circuit working today.  You can see the resulting I and Q in the picture at the top.   But I am discovering that there may have been wisdom  behind those divide by 4 circuits.  My opposite sideband suppression isn't as good with this /2 scheme as it was with the AD9850 divide by 4.  I'm still trying to figure out why. I may have to go back to divide by 4.  Stay tuned.    

Michael's Log: AA1TJ Has FIVE Contacts with the Unijunction Transistor at 1-2 milliwatts

Michael writes:

Dear Friends, The UJT transmitter circuit was improved considerably today. The power output has increased to 1.48mW and the start-up "whoosh" is now far less objectionable. It's currently running in beacon-mode at 3687.8kHz. I'll resume "CQing" as soon as I've returned from an hour's walk in the woods. I hoping to work K1QO among others. 73, Mike

Added five QSOs today. Seabury/AA1MY is in Maine...exactly 100 miles from my doorstep. It's wild to think that we made a one-hundred mile radio contact on a unijunction.

Beautiful BITX17 Presentation by Chris PA3CRX

This is a really amazing presentation on our beloved BITX rigs.  This presentation takes the viewer from block diagram to schematic to photos of the actual circuits and throws in great graphics showing spectra and filter curves etc. 

There is no sound.

Here is the link in case the embed above doesn't work:

https://prezi.com/yn2loy4mi0wo/bitx20/

Thanks Chris!

A Probable First: First Ever Radio Contact Using Unijunction Transistor as the Transmitter

AA1TJ writes:

I spent most of a week working to raise the RF output power from my unijunction transmitter to nearly 1mW. I was rewarded this evening with two contacts.

Jim/W1PID exchanged (599/449) signal reports with me from Sanbornton, NH (112km) at 2210z!

Dave/K1SWL did the same (589/229) from Newport, NH (95km) some four minutes later!

I should think these were the first-ever radio contacts made using a unijunction transistor as the transmitter.

FYI: my receiver was comprised of a single 1N34a germanium diode mixer followed by a single 2N35 germanium transistor audio amplifier. Great signals on this end.

Wikipedia on Unijunction Transistors: https://en.wikipedia.org/wiki/Unijunction_transistor

New VFO for the Frankenstein R2 Phasing Receiver

I've wanted to change the VFO in my R2 phasing receiver.  The AD9850 DDS VFO with a divide by 4  I-Q generator limited me to 160, 80 and 40 meters.  But an Si5351 chip will go up to 160 MHz.  With a divide by 2 I-Q generator, this should allow me to cover 160 through 6 meters. I got the Arduino, LCD and rotary encoder all working tonight.  Thanks to Thomas LA3PNA for the code, and to Tom AK2B for help with the Arduino. The Si5351 board that you see sitting atop the Arduino is the work of Dean AC9JQ.  Thanks Dean.  

The flip-flop and inverter IC's should arrive this week.  That will allow me to finish up this VFO conversion project.

Dead Chickens and Fake Transistors in Medellin Colombia: HK4DEI's Micro 40 DSB Rig

Daniel HK4DEI wrote to report that page 149 of the SolderSmoke book was providing some solace and comfort as he struggled to get his version of Peter Parker's Micro 40 Double Sideband rig going.  He was having problems with the amplifier.   He was almost at the point of sacrificing chickens to Papa Legba.  I wished him luck and told him to hang in there. 

Elisa saw my e-mail to Daniel and complained that I hadn't given him the solution to his amplifier woes.  I tried to explain to her that there are sometimes things in this universe that are just UNKNOWABLE.  C.F. Rockey W9SCH (who alerted us in SPRAT 22 to the chicken sacrifice option) spoke of transistors that exhibit "quantum mechanical necromancy."  Rockey explained that when this happens, "The transistor simply turns up its toes and dies. Not even an Atomic Physicist can tell you why!"  

But Daniel persisted.  And he won the battle:

Hey Bill

Did you kill some chickens already? If you did, THANK YOU!  If you don't, then please enjoy a nice sancocho de gallina for me.

But seriously... guess what?

FAKE TRANSISTORS!!!!

I knew I couldn't be screwing everything up so badly and VK3YE's circuit couldn't be so wrong.

I was getting nuts trying to understand why it wasn't working, changing a single inductor could fry the final instantly or not getting any power out at all (?) also my final BD139 was getting extremely hot, and many of them died with no apparent reason (Page 149!!!!).

I ordered a "good" deal of BD139's and BD140's combo for an incredible low price from [A WEB SITE], I've ordered many *apparently good components from that site with no problems so far... mainly resistors and capacitors. Having tried everything to get my circuit working and after some quick online search about fake transistors from china my suspicions grew considerably and I remembered some -other- BD139's I had ordered from Amazon some time ago.

I proceeded to solder the new transistors in place in my PA and Bingo! No more heating of the final and about the expected 0.5W out from my first DSB homebrew rig. I quickly reported to a fellow homebrewer in a local net and the report was amazing! 59 +10, the final transistor was comfortably warm to the touch and my mind could finally rest... lesson learned! What an electromagnetic achievement!

Just wanted to share my success Bill and thank you again for you book and you kind response.

Please say hi to Elisa and the Cristalinhos from a fellow Latin friend.

Clear Skies.

73/72 from Colombia!

Daniel

HK4DEI

RESISTANCE IS FUTILE! Diode Tunnels in Germany and Vermont

Peter DL3PB's Zinc Negative Resistance Transceiver

Michael Rainey AA1TJ's work with tunnel diode rigs has provided much grist for the SolderSmoke mill over the years, as has the tunneling of Peter DL3PB:
http://soldersmoke.blogspot.com/search?q=tunnel+diodes

They are back at it!

Michael updates Peter (and us!) us on his efforts of this week:

Grüss Peter!

Thanks for the nice message. Yes, I knew that you were going to be QRV with your ZnO transceiver but I never heard if you had made any contacts. I guessed that you had not, otherwise I'm sure you would have let me know. 

Again, I think your circuit looks really great! It's amazing to think you managed to squeeze 500uW from a scrap of oxidized zinc-plated steel. Even if you didn't make a contact, what you are doing is really fantastic. Congratulations on the creation of this amazing radio!

Okay, so I spent most of the afternoon at the workbench. Thus far I'm only using a single SRD (step-recovery-diode...1N5401 rectifier). Of course the result is a unipolar pulse. The idea did work as planned, however the power only increased by 2.24dB. The maximum RF output power is now 230uW. At least the SRD makes a pretty pulse :-)   

Please find two scope captures attached to this message. The first (0002) shows the SRD generated unipolar pulse. As you can see, the pulse width is nearly perfect for the job. The second trace shows the output RF waveform. The worst spurious energy is ~20dBc. The second image shows the 507kHz waveform at the unijunction emitter along with the output RF waveform.

The beacon is presently off the air, but I look forward to trying my luck tomorrow with a back-to-back pair of SRDs. A bipolar pulse pair will provide a shock impulse once every 3.5 cycles, instead of once every 7 cycles with the present unipolar drive pulse. The bipolar pulse pair should result in increased RF output power as well as a slight spectral improvement.

It's only a matter of time before you make a ZnO QSO, Peter. As we always say, the difficulty merely sweetens the eventual success. 

A broadband measurement of my output power (using an AD8307 log-amp power meter) indicates 139uW. Spurious frequency energy accounts for 2uW, leaving 137uW at 3.552MHz. I believe this is roughly the output power produced by your ZnO transmitter? 

This morning I'll attempt to increase the unijunction (UJT) 80m RF output power by inserting a pair of back-to-back standard-recovery power supply rectifiers (1N5401-ish) at the  UJT base-2 to ground node. Thus far I have relied exclusively on internal UJT nonlinearity for the generation of harmonic energy. I've reason to believe the minority carrier charge-storage capability (normally a defect, but hopefully a virtue here!) of these rectifiers will efficiently produce a bipolar pulse-pair every 1/500kHz seconds resulting in an odd-order comb-spectrum. At least that's the plan...we'll see how it works out ;-)

Peter, I never heard the results of your ZnO DXpedition? Any luck OM?

Okay, I'm off to the Hobbit-Hole. My heartfelt thanks to you all for your shared interest in this cock-eyed project.

73,

Mike, AA1TJ       

Peter, DL3PB, in Germany respond with amazing news of his own.  Peter is homebrewing his own tunnel diodes, using Zinc Negative Resistance Oscillators.  No store-bought appliances for him!

At this point you really have to visit the pages of Nyle K7NS

http://www.sparkbangbuzz.com/els/zincosc-el.htm

and

http://sparkbangbuzz.com/zinc-osc-2/zinc-osc3.htm

Nyle tells of building a little microwatt transmitter, and, once the snow melted, climbing a hill 5 miles from town to see if he could hear it.  This reminded me of young Marconi's early efforts in Bologna.

Peter writes:

Hi Folks,

Mike, your plan on how to increase output-power sounds reasonable –  yes, a few dB could really help, to make reception a bit steadier and thus allow a QSO.

Well, I thought we had already talked about the ZnO TRX attempt, but obviously we didn’t. The reason is dead simple - It didn’t work.

[ The ZnO TRX is a minimalist 80m band transceiver with a homemade tunnel-detector-diode as the only active device –  based on Nyle’s K7NS experimentshttp://sparkbangbuzz.com/zinc-osc-2/zinc-osc3.htm – please find attached an early schematic ]

Three days in a row after Xmas I tried for several hours each, I had announced the activity on QRPSPOTS and the German QRP Forum. Thus several guys
within the right distance were really trying hard to copy. I used different temporary antennas, mostly verticals, but also a sloper dipole - nada, niente , nothing.
One or two OMs reported weak CW signals on the scheduled QRG, but too deep in the noise, to even make out, whether it was me or someone else.

Yes, power is more or less comparable, actually it’s 0.5mW +/-3dB depending on the day’s form of the homemade tunnel-detector, but I guess all my antennas are
some dB behind a full-size dipole, so at the end it’s pretty much the same.

Folks were very cooperative during the test itself, but after it was clear, that it had not worked, the usual trolls showed up to explain, why that never could have worked...
I plan another test within the coming week e.g. during the PA-contest next weekend ( I’m only 30km from the dutch border ) with a base loaded 15m vertical –
be assured, you’re the first to hear about any success in terms of QSO or just being heard anywhere.

What would we go for, if everything works as expected and/or right from the beginning – or as Jim said it : What fun...

73!

Peter/DL3PB

Finally, Alan Wolke provides a very illuminating (as always) explanation of tunnel diodes):

AA1TJ's 150 Microwatts Heard at 112 Kilometers -- "To Boldly Go Where no Unijunction Has Gone Before."

AA1TJ reports: 

Breaking news from W1PID... "Mike! I just copied the beacon. I got 'VVV de AA1TJ 150 uw' and it faded out. 2146Z on 3551.95MHz" That's it! Jim copied a message produced by a lowly unijunction at a distance of 112km. How's that for cool! In a nutshell... the unijunction runs as an R-C relaxation oscillator at ~500kHz. A quartz crystal at the emitter frequency-locks the sawtooth waveform to 507kHz. The 7th harmonic is admitted to the antenna via a bandpass filter. The RF output to DC input conversion efficiency is all of 0.1%. Heat-sink? Check! Mission statement:
"...to boldly go where no unijunction has gone before." Cheers,
Mike, AA1TJ

I think the really cool thing is that EM waves are once again flying out of the Vermont Hobbit Hole, propelled into space by the poet laureate of QRP.

QST de AA1TJ -- Please listen for Mike's Microwatts!

QST de AA1TJ...

I've a 150uW transmitter built from a single unijunction transistor currently running as a beacon on 3552kHz. If my New England amateur radio pals would be so kind as take a listen for it I'd be most appreciative!

Alan Wolke W2AEW Builds a Michigan Mighty Mite (Video)

We are honored to induct Alan Wolke W2AEW into the Colorburst Liberation Army.  And for his valiant effort to build and explain a MMM Low-Pass filter, he is immediately promoted to the rank of CBLA Two Star General.  Congratulations General Wolke.

As is the case with all of  his videos, this one has already had an impact far and wide.  Ian writes from far-off Western Australia:

Jan 27 at 6:19 PM

G'day Bill,Just in case none of your other correspondents have brought it to your attention, here is a great video W2AEW has put up showing really clearly the positive effect of a low pass filter on the output of the Michigan Mighty-Mite.

It made me appreciate the benefits of an LPF more fully. It's always been clear to me that the harmonics would get rolled off, but in my head I hadn't made the connection between that and the improvement to the beautiful smooth sine wave that we are working towards.

Anyway, I thought you, and your mate Steve "Snort Rosin" Smith may be interested.

Thanks to you and Pete for Soldersmoke, I'm sure you're responsible for keeping the flame alight in many a ham.

73,Ian VK6MIB

And Steve "Snort Rosin" Smith, the guru of low pass filters, observes:

Of course, to work properly in the land down under, the inductors must be wound in the opposite  direction as those in the Northern Hemisphere :-P .

Seriously, there is a lot to be learned from the lowly Mighty Mite especially regarding impedance matching; not to mention LC circuits, link coupling, amplifiers, oscillators, etc. .  What fun!

73.......SR