Podcasting since 2005! Listen to Latest SolderSmoke

Saturday, May 12, 2018

NN2K's Beautiful Pine-Board Al-Fresco Thermatron AM Transmitter


On Saturday mornings (around dawn) I often listen to the Old Military Radio Net on 3885 kHz.  I find it inspirational.  This morning the inspiration was provided by Rick NN2K.  His signal from Binghamton New York was makeing the trip to Northern Virginia.  When I heard him mention that he was using a "Pine Board Transmitter" I felt the urge to look for a picture.  QRZ.com provided the photo.  

Rich says he built this rig in January 2018 based on a QST article by Bob Heil.   FB Rich! 
And thanks to Ted W3PWW for running the Old Military Radio Net for so many years. 


Tuesday, May 8, 2018

KE4MIQ's Repurposed Raduino Receiver


FB James -- Really glad you are listening,  and that you are having fun with a Direct Conversion receiver --- souped up with a Raduino! 


Bill, Pete

Just listened to #204. (New Listener)
You talked about using the Raduino with other radios.
I bought one of Mike Hagen's RaduinoXs to use with my Bitx40. So, I have repurposed my original Raduino as a VFO for my 4SQRP ZZRX-40 DC receiver. I used Allards's v1.26 with a few code changes to tune 7.000 to 7.300. It's currently al fresco on a piece of Hobby Lobby foam board. I may "cabinetize" at some future date.
Attached is a pic of the ZZRX-40, Raduino, and Goodwill Sony speaker with Jameco stereo amp, all running off of Harbor Freight 9v Nimh rechargables.

So far I have heard over 40 states and 20 countries with a 65ft piece of wire in the rafters.
73s
James
KE4MIQ

Saturday, May 5, 2018

SolderSmoke Podcast #204 April 1, SPRAT Cover 2, uBITX mania, MAILBAG


SolderSmoke Podcast #204 is available! 

http://soldersmoke.com/soldersmoke204.mp3

5 May 2018

April 1 Recap -- We thank you for your support! 

Pete's Rig on Cover of SPRAT 174 

uBITX Mania

uBITX Dual Conversion Design

uBITX Gettng more out of the Arduino/Si5351 combo

uBITX KD8CEC's amazing software

uBITX Future Possibilities

uBITX On-the-Air Experiences, with CW too! 

MAILBAG

KD8CGH's Hyderabox -- THERE ARE TWO! 
QSO with N1AW's cardboard uBITX
DuWayne on QSO TODAY
Jack 5R8SV -- Radio Gods NOT Happy
Jack Purdum W8TEE -- Thanks OM
Charles AI4OT
Chris KB4PBT 15 inch telescope
John WJ0NF Reading SolderSmoke
Ken W8KTP Ordering a uBITX 
Darren KG7KOI  Listening
Gary AK4NA  New Word:  "Cabinetize" FB OM! 


Sunday, April 29, 2018

"The Thrill That'll Hit Ya..." AGAIN! Three cheers for Pete, SPRAT, and GQRP


On the cover of issue 173 of our beloved SPRAT magazine they had my little Direct Conversion receiver.  We joked on the podcast about the old song by Doctor Hook about getting on the "Cover of the Rolling Stone."  Well, on the cover of issue 174 they have one of Pete's magnificent creations.  

Thanks again to the guys who put so much work into SPRAT magazine.  They are now looking for some help.  Please subscribe, and check out page 4 of issue 174 for details on the help that GQRP is looking for.  


Sunday, April 22, 2018

KC1FSZ's Above Board, Al Fresco, Free Range, QRO, 4-Foot-Long, Wood-Based BITX


DON'T BOX IT UP BRUCE!  LET THAT RIG LIVE FREE AND BREATHE!  

COULD THIS BE THE WORLD'S BIGGEST BITX?

Hi Guys:

First off, congrats on back-to-back SPRAT covers.  

I’ve succeeded in my QRO quest.  Now I’m running the finals from 28V using a home-brew linear power supply and getting about 20W out.  LM723 + 2N3055’s.  I’m making a lot more contacts too.  The only problem is that the “Peppermint Line” is close to 4 feet long now! (Photo below).  I don’t know how N6QW gets his rigs packed into such small cases.  Putting the various boards in edge-wise will probably help a lot, so that’s going to be my approach to the final packaging job.

73s, 

Bruce KC1FSZ



Saturday, April 21, 2018

Hyderabox! uBITX in a Lunch Box


Oh man, I'm sorry I missed this one.  John sent it to me in January, but it got lost amidst all the uBITX messages.  

I like it!  It shows that I am not the only one guilty of re-purposing Benton Harbor Lunch Boxes.  

But what should we call it?  It is now more Hyderabad than Benton Harbor.  How about Hyderabox?  That's it!   

Bill
  You mentioned in your last podcast recycling "Benton Harbor Lunch Boxs". Many decades ago I talked my Junior High shop teacher into letting me build a Twoer instead of his lame project. Over the years  2 meter AM and the Twoer faded away. 
I recently revived a Lunchbox case for my uBitx. I added a Sotabeams CW filter that is controlled by the old T/R knob. Down the filter is bypassed, up one is wide CW and up two is narrow CW. The green pilot light light is a CW tuning indicator. 
I use KD8CEC's code which cleans up many small problems and adds a memory keyer and CAT control to the uBitx.
I modded KD8CEC's code to remove the paddle sense segment so that it only works with a straight key. This makes the keying much cleaner. 
First contact with the modded uBitx was this morning. With 5 watts out I got a 599 from K3Y/7 (K7QBW) in Oregon back to me in Ohio.
    Bob    KD8CGH

Tuesday, April 17, 2018

N1AW's uBITX -- Cardboard Panels, and the Mic in a Sharpie


On Sunday night at 7 pm local on 7.277 MHz BITX users gather.   This week was the debut of my uBITX.  I was able to make only one contact before we were over-run by the Rookie Roundup, but that contact was a good one.  Above you can see N1AW's FB uBITX.   The front and back panels are made of cardboard.  The mic holder is from a re-purposed Sharpie marker.  FB Al.  Thanks for the contact.  

Sunday, April 15, 2018

Carpentry and Socketry for the uBITX


Yesterday I decided to spend some time at the bench -- I wanted to get the uBITX boxed up.  My basswood box had arrived from Amazon on Friday.  It was time for what George Dobbs G3RJV called "socketry."  

First, the back.  I figured I would need five connectors back there.   Connectors for 12V DC, speaker, and antenna would be needed right away (it is my preference to have the speaker connector on the back of the BITX).  Looking ahead, I might want to also have a jack for T/R control of my linear amplifier, and a jack for 24 VDC if I want to go wild and put more voltage on the drains of the IRF510s. So I put two extra holes in there.  


Basswood is SO easy to cut.  I put the LCD in the center of the front panel, and opted to put the board close to the front of the board.  This avoids the need for jumpers to connect the Raduino to the LCD, and it keeps the lines to the front panel controls and connectors very short. I mounted the board on the spacers that came with the BITX, drilling holes the bottom of the basswood box.  It all fit quite nicely. 


I would need to put two jacks on the front panels:  key jack and mic jack.  And I'd need two controls: main tuning and AF gain.  I used hole saws to cut holes big enough to accommodate the four items. 


The controls and jacks were then placed on two small pieces of copper clad board.  These then went on the front panel.  

Wiring up the uBITX was  easy.  I just followed Farhan's instructions.  I did the wiring AFTER placing the boards and controls in the box -- this helped me keep all the wires at their optimum length (not too long, and more important -- not too short!).  If you do it this way, put a cloth over the boards so you don't drop solder blobs on the uBITX. 

Farhan's uBITX fired up nicely as soon as I applied power.   The receiver really sounds nice.  I hope to make some contacts with it today. 

Three cheers for Farhan! 


Saturday, April 14, 2018

Boxing up my uBITX -- Question for the Group


Our friend Rogier and I are involved in an East Coast -- West Coast uBITX launch project -- we plan to assemble our uBITXs together (more or less, via Skype) and then get them on the air. 

As has been my recent practice, I have opted to put my uBITX in the same kind of wooden box that I used for my three scratch-built BITX projects.  See above. 

Now, due to Farhan's wizardry the uBITX is considerably smaller than the box.  This is, of course, a good thing. It leaves room in the box for many bells and whistles.  

But here is my first box design question

Should I put the uBITX board to the front of the box so that the LCD can be connected to the board DIRECTLY via the connector on the Raduino board (no jumpers needed), or should I put the uBITX board to the back of the box so that I can stick the PA heat sinks out the back?   In the later case I'd have to use 4 inch jumper cables to connect the LCD to the Raduino.  This use of jumpers seems to increase the possibility of noise from the display. 

What say the Knack Wizards?  Back of the box with LCD jumpers, or front of the box with no jumpers but heat sinks inside the box? 

Sunday, April 8, 2018

AMAZING 1999 Video on the Invention of the Transistor at "Hell's Bells Laboratory"



Thanks to Armand WA1UQO for alerting me to this.  I really liked the book -- "Crystal Fire" -- that this 1999 video is loosely based on. I'm also a fan of the narrator,  Ira Flatow, whose melodious voice is heard each week on NPR's excellent "Science Friday" radio show. 

A few observations and thoughts on the video: 

-- I liked the irreverant Calypso song "Hell's Bells Laboratory."  It looks like those folks had a lot of fun.  And wow, Shockly's secretary was named Betty Sparks.  TRGHS. 

-- I have the same big Variac on my bench.  And I have one of those "third hand" devices.  

-- I'd like to build my own replica of the point contact device with the triangular piece of lucite and the gold foil. 

-- While Shockley seems to be the real bad guy in this story (he seems to have all the bad characteristics of David Sarnoff,  Lee DeForest, and Steve Jobs),  I liked the his use of "physical intuition" to understand devices and the problems they were meant to solve.  

-- The image of the two Japanese founders of Sony working in the late 1940's in a bombed out department store was very powerful.   

-- Although I came on the scence a bit later, I WAS one of those kids who used a transistor radio and an earphone to surreptitiously listen to rock-and-roll music. 

-- "More transistors are made each year than raindrops fall on California."  Hmmm.... 

More info here:  http://www.pbs.org/transistor/
Extra interviews:  http://www.pbs.org/transistor/tv/index.html

Friday, April 6, 2018

Solder Haze -- Sing Along with N8NM and Jimi Hendrix


Back when some us were thinking of new names for the podcast, Steve, N8NM thought of Purple Haze by Jimi Hendrix and came up with this set of lyrics (listen to the video above to get the tune). 

Solder Haze, all in my brain
Making rigs, some don't work that great.
They're acting funny, but I don't know why
Kill some birds for that Legba guy.

Solder Haze, all around.
Don't if I should turn the bias down.
Or maybe I should raise the Vcc
Oh, it's a FET, that would make it Vdd.

Solder Haze, all in my eyes
Don't know if it's day or night.
You got me blowing, blowing my mind
Come tomorrow,  I won't be to work on time. 


Pete, WB9FLW took a more, well, defiant line.  He came up with new name for the podcast that sort of captures the shocking level of indignation that this completly bogus story generated.  Pete suggests that we simply call the new show: "FLUX YOU"

Thank you gentlemen.  You are both, in a way, poets.  And Hendrix would, I think, approve. 

Now, will the Wizard of Newbury Park pull out his guitar and get to work on this?   

Monday, April 2, 2018

REPRIEVE! SolderSmoke Saved by a Loophole!

First, let me thank the many, many MANY, loyal listeners from around the world who wrote in with expressions of support and sympathy.  Special thanks to our UK listeners who were notable in their indignation for they saw as a blatant example of US litigiousness "gone mad."  One loyal British listener went so far as to pledge to immediately end his patronage of the Birmingham Vaping business known as SodderSmoke.  We found this quite, well, suprising.   But we were chuffed, nonetheless.  Thanks OM! 

The expressions of concern were really quite touching.  One listener asked if he should  -- in an effort to keep us out of hot water -- destroy his SolderSmoke coffee mug.  With fans like that, well, what can I say?  

In responding to the legal crisis, our listeners displayed ASTOUNDING creativity in their crafting of alternative names for the podcast.   

Buck seems to have a real "knack" for name-smithing. He wrote: 
The easiest would be Solder Haze - it's a simple scan & replace.  But
if the trademark trolls grabbed 'haze' too...
Some other ideas:
Eutectic Point
The Solder Wick Chronicles
Sixty-Forty
PbSn
The Joy of Soldering
Fahrenheit 368

John suggested the rather toxic  "LeadVapors," but we feared that that one might lead to even more trouble, perhaps even with the EPA.  (But, no, wait -- no worries there!) 

Gary suggested SolderSuckers.   I briefly thought of the many people who wrote in (see above) but concluded that that one just sucked.  No. 

A number of listeners suggested legal counterattacks and fund-raising effots.  (We did get one unsolicited donation!)   One fellow suggested fighting fire with fire by having us trademark the phrase "Chicks dig it" and then just letting the money roll in. 

One devoted radio amateur said that he "informed his club and launched a letter writing campaign."  Thanks OM!  Keep those cards and letters going... 

There were, unfortunately, many disparaging comments about California, and "pot-heads," and "California pot heads."  But hey, Dudes...  they don't mind.  They are not going to let you harsh their mellows. 

Stewart tried to claim that there is some sort of UK rule that says that things like this can't be carried on past noon local time in Britain.  Ha! I said.  We are no longer bound by Imperial edicts.  

Similarly, Peter in Australia complained that the story reached him on April 2, rendering it null and void.  Sorry Peter, these are UTC operations my friend.  Time to wake up and join the rest of the world!

Well, let me get to the point:   The beloved name of our podcast and blog has been saved by a loophole.  You see, any legal challenges of this nature launched and announced on April 1st of each year are HIGHLY likely to be found, on even casual examination, to be be null, void, and totally bogus. 

So no, 

-- PETE'S COMPUTER WAS NOT SEIZED BY A COURT ORDER. 

-- THE CALIFORNIA MARIJUANA INDUSTRY IS NOT PLANNING ON MARKETING SOLDER-SCENTED WEED. 

-- THERE IS NO BIRMINGHAM COMPANY CALLED "SodderSmoke" (JUST THINK OF THE TRANSLATION!) 

-- WE ARE NOT BEING SUED FOR TRADEMARK VIOLATION BY AN EVIL MARIJUANA-VAPING JUGGERNAUT.  

But we thank you for your support.  And, to make it official:  APRIL FOOL!  73  Bill 

Designer: Douglas Bowman | Dimodifikasi oleh Abdul Munir Original Posting Rounders 3 Column