We got some questions on this and Pete was kind enough to write up some notes on the topic. We may talk more about this during the next podcast (Saturday):
Broad Band
Impedance Matching Transformers.
Broad Band impedance matching transformers are designed to transfer power
over a wide frequency range. More basic you have an amplifier that has an output
impedance of 200 Ohms and you want to match that to a 50 Ohm load.
So what is the magic decoder ring so that you get a 4:1 match, ie going
from 200 Ohms to 50 Ohms. Getting technical for a moment the maximum power
transfer theorem says maximum power is developed when the source is matched to
the load. The Broad Band Matching
transformer enables that to happen over a wide frequency range.
So how do we get from 200 Ohms (the source) to 50 Ohms (the load)? Just as there are many
airlines that fly from LA to NY so it is with the matching approach. We will
cover several.
First a short discussion about broadband cores themselves. One of the most
common cores for HF work is the type 43 core which is good up to about 50 MHz.
For transformers up to 200 MHz then the type 61 are a better choice. Typically
at HF the FT -37-43 is one of the more common ones see (3/8 inch in diameter),
as is the FT-50-43 which is ½ inch in diameter. The iron powder cores are not the 1st choice
for broad band matching.
#1 Way:
Build a transformer that has a
primary of x number of turns (and since it is large, 200 Ohms will have
more turns) and the secondary will have y number of turns ( and since it is
smaller, 50 Ohms, will have fewer turns.) The transformer action is based on
the ratio of the Primary turns Squared to the Secondary Turns squared. Our
transformation is 4:1.
Thus if we divide the primary turns squared and divide it by the secondary
turns squared the result is 4. Here are some example: if we had a primary of 8
turns ( 64) and a secondary of 4 turns (16) – 64/16 = 4. So that is our transformer a primary of 8 turns and a secondary of 4 turns. When building
these transformers use two different colors of wire as that makes it much
easier to identify the windings. Observe the phasing, meaning the end you
connect to the collector of your output transistor is the start end. That same
start end for the secondary winding is the output “hot” side of the secondary.
#2 Way.
The same ratio holds in going from 200 to 50 Ohms. But this time we will
use a single winding of 8 turns and at 4 turns we will have a tap for the 50
Ohm point. Since that tap will very likely have Dc on it connect a 100 NF cap
at the 4th turn winding and this is the output. What you have just done is
create an auto transformer.
#3 Way.
At time one may have an oddball transformation and you can cascade
transformers and multiply their individual turns ratios. At one time I needed a
9:1 transformation. I built a 2.5 transformer and then hooked that to a 4:1 and
the result was a 9:1 transformer.
The attached table has “worked out” some common matches that are often needed
like matching a 50 Ohm amplifier to a 500 Ohm Crystal Filter which is a 10: 1
match. This is easily done with a 6 turn primary (50 ohms 6^2 = 36) and the
secondary has 19 turns ( 500 Oms 19^2 = 361). 361/36 = 10.03:1. Close enough for ham radio! The 1st way is probably more preferable for this
application.
Pete N6QW
11/2014
Our book: "SolderSmoke -- Global Adventures in Wireless Electronics"
http://soldersmoke.com/book.htm
Our coffee mugs, T-Shirts, bumper stickers:
http://www.cafepress.com/SolderSmoke
Our Book Store:
http://astore.amazon.com/contracross-20
