Just go to http://soldersmoke.com. On that archive page, just click on the blue hyperlinks and your audio player should play that episode.
http://soldersmoke.com
This one is kind of "out there," on the fringes of radio respectability. But on the other hand Nate KA1MUQ has just took to a new limit the old ham radio tradition of raiding the kitchen for items that will serve the bases of support for new rigs. Usually, these items are wooden breadboards (hence the term). Nate has taken this quite a bit further, appropriating an entire frying pan because of its copper bottom. Nate reports that there is good news and bad news: The good news is that the receiver is working. The bad news is that his wife has banned him from the kitchen. It takes a brave and dedicated homebrewer to do something like this. Kudos Nate. But you probably should stay out of the kitchen.
Nate's receiver sounds great, and had provoked some much-needed humor on Discord: There were comments about too much bacon frying noise. And about the frequency readout being eggzactly right. Dead pan humor, and the possibility of a pan-adapter. FB!
Thanks a lot Nate and congratulations.
---------------------------------------------
For more information on how you too can build the receiver:
Nice job Piotr! Congratulations! In his comments he captures well the excitement that comes from listening to receiver as it first comes to life:
Piotr writes:
It's alive! Thank you Solder Smoke team. My winding on PTO bit loose, I think I'll just hot glue gun it. Tuning is delicate, but front panel added some friction. Need to swap audio pot (used linear I had handy), and speaker is 12R (from junk box). Audio stage has a lot of gain - that stage alone did pick up loud AM station with my finger as antenna :). Thanks again de Piotr KD9NHZ
For more information on how you too can build the receiver:
FB Steve! Your receiver looks and sounds great! Congratulations!
Steve writes:
Thanks to Bill and Dean for all their work and promotion of this project. I learned alot and had fun. The receiver works well now after much tweaking. I need to finalize how the boards will be mounted. I am thinking of mounting the BPF and audio amp boards vertically on the edge of my small piece of wood and create a front panel using a PCB to mount a on-off switch, volume control. on/off LED, and the speaker/headphone jack. I also want to add a rear PCB to hold an antenna jack and power jack.
-------------------------
For more information on how you too can build the receiver:
When I first saw Martin's boards, I thought I was looking at something that was not really Manhattan style. But I was wrong -- Martin had simply drawn grid squares on his boards. He used MeSquares for his non-ground connections. The SSB his receiver was picking up sounded great.
Martin is a relatively new ham -- he started in 2020. It is really nice to have Scotland represented in the group.
Martin writes: One of the main things I learned was how to really start to use my oscilloscope. The band pass filter proved to be challenging as I initially placed my trimmers incorrectly and it took quite a while to find the problem. I'm looking at this as a potential high school project, so all my soldering was with lead free solder, as I run a community interest company providing tech workshops for disadvantaged kids. I would like next to look at building a complimentary transmitter. Will also have a look at the mods and upgrades.
Martin has noted the touchiness of the main tuning knob. One of the mods he should look at is the one that allows for easier tuning across the 40 meter band. It is described in detail in a post on mods-and-modifications.
Thanks Martin, and congratulations.
---------------------------------
For more information on how you too can build the receiver:
Mark KI5SRY came up with a very innovative solution for the tuning dial problem. See above. My solution was much less sophisticated: At the suggestion of VK3YE, I just put a calibrated card underneath the screw. By looking at the screw edge from above, I could get a rough estimate of where I was in the band:
Looking back on his successful build of the receiver, Mark wrote:
You made this pretty straightforward. My biggest challenge was trying to understand what was really happening in the circuit.
I learned how to use my oscilloscope, seeing the oscillator come to life was great.
I would like to build a transmitter or a complete transceiver.
Bill, thanks to all of the effort you and Dean are putting into this project. There was definitely a magical feeling dialing in and getting legible sound out something built on my bench.
Very cool Mark. Congratulations!
---------------------------------
For more information on how you too can build the receiver:
Wow, Jeff N0NQD built a beautiful receiver, and has been bitten bad by the homebrew bug. Jeff admitted that he recently went to a gala with his wife. He was preoccupied with the problems he was having with his DC receiver. Suddenly DURING THE GALA he remembered having mis-identified two capacitors in the mixer. So he and his wife HAD TO GO HOME FROM THE GALA so that he could fix the problem. And apparently he is still alive, and married! Amazing!
Jeff wrote:
I have been a ham for just about 40 year and typically build kits lots of them most recent the QMX. I found a new passion and seemingly addiction now because of this build. My next Home-brew project is probably going to be a transceiver or a complex receiver not sure what type just yet. It has been so much fun and highly distractive to be apart of this Soldersmoke DCR family. And hope this continues!! Thank you and 73 Jeff N0NQD
Jeff N0NQD's Bench
Thanks Jeff. Congratulations!
---------------------------------
For more information on how you too can build the receiver:
Erik built a really nice receiver. I was glad that he took to heart our advice on the need for a large, insulating tuning dial. He made one! As he made this entire receiver.
Eric wrote:
I would like to make a homebrew QSO! I am learning CW, mainly because I find it easy to use QRP/POTA. I have a Michigan Mighty Mite, but it has not reached farther than my backyard yet, so a CW transmitter in the single Watt range would be a great next project.
Congratulations Erik!
---------------------------------
For more information on how you too can build the receiver:
All the way through, Ryan displayed a desire to really understand each of the four circuits included in this receiver. He wanted, as Maxwell said, to know not only the "go of it" but "the particular go if it." FB!
Ryan wrote:
Here's a short video of my receiver in action. I'm very pleased to be receiving real radio! I'm too inexperienced, so don't really know if this is good or bad performance for this receiver. This is about as good as I've gotten so far. A few people I can understand well, but many are not really intelligible. Thanks to everyone, this is a fun project!
I think it sounds great. Tuning in an SSB station with a DC receiver is an aquired skill -- we all get better at it over time.
Congratulations on building a really nice receiver Ryan.
-----------------------------
For more information on how you too can build the receiver:
Above you can watch and listen to Wayde's receiver as he tunes across 40 meters. It sounds good, even though Wayde is thinking about some improvements.
It was highly appropriate that Wayde's first reception report should be of CHU Canada, the Canadian time signal on 7.850 MHz, a bit above the 40 meter band, but clearly in tuning range for an unmodified SolderSmoke direct conversion receiver. CHU is probably unique in the world in that it is transmitting the carrier and JUST ONE SIDEBAND. It transmits only the upper sideband. This makes it clearly detectable by our receiver. As Dean pointed out to Wayde, all he had to do was "zero beat" the carrier with the PTO signal (tune to the point where they are on the same frequency and the audio tone disappears). Because there is only one sideband, the direct conversion receiver can demodulate it very well. If there had been two sidebands, this would have been a standard AM signal, and our little receiver -- which does very well with SSB and CW -- would have been unable to demodulate the signal without distortion. (For an explanation of why this is, see: https://soldersmoke.blogspot.com/2022/12/but-why-why-cant-i-listen-to-dsb-or-am.html Warning -- this is kind of in the "advanced course" category.)
Here is an overhead shot of Wayde's receiver:
This is a really nice build. The use of what appears to be a kitchen cutting board harkens back to the early days of radio when young hams took the cutting boards from their mothers' kitchens and used them as bases for rigs. This is origin of the term "bread board." Frank Jones continued in this tradition by building most of his rigs on wooden boards. Wade's DC receiver continues in that tradition.
Wade was able to decode some FT8 picked up by this receiver and recorded on his phone:
Congratulations Wade!
----------------------------
For more information on how you too can build the receiver:
Ken W4KAC tells me that the tuning knob that he used to minimize hand-capacitance effects on his PTO started out as a gear in a leaf blower. I commented that the engineers who designed that gear surely never thought that it would someday be used in a homebrew direct conversion receiver.
Ken lamented the polemical nature of the SSB discussion captured in the above video, but the clip does give a good demo of the SSB capabilities of Ken's receiver. And the video gives some nice close-ups of the receiver itself.
Ken is a CW guy, and he has already homebrewed a QRP CW transmitter that he hope to pair-up with the receiver. Here it is:
Good morning. Just wanted to say, don't give up if your receiver is not quite right. Mine was working, I even posted a video here. When building the AF amp from the transformer end back, the Q4 stage was fine. I added Q3 and had a "motor-boating" oscillation when I applied a signal. I tore it all off the board and started over. I still had the problem, so being stubborn I continued on and kept adding more filter caps to quiet it down all I could. The receiver worked and sounded pretty good during the day when I copied WA4FAT and others. That evening was a different story when the band was working well and very full of signals. Very strong stations were ok, but I was getting lots of "hash" and noise other than normal band noise. FT8 was breaking through weakly all over the band along with other unidentified stuff. Yesterday morning I grabbed a new piece of copper clad and built and entirely new AF amp. It tested properly all through the build. Instead of installing that board I decided to find the problem with the original. I "thought" I had used new transistors when I rebuilt it the first time. Turns out I had probably put the original Q3 back, because replacing it cured the problem. I had an entirely different receiver last night. A pleasure to listen to. Don't give up like I did at first!!
Ken went the extra mile by building a SECOND Direct Conversion receiver. So he may soon get TWO Hall of Fame credits. Here is the second one that Ken built:
Jason did a great job on this receiver, hanging in there as he worked to overcome techincal difficulties, some of which were related to test gear. That is a big part of the homebrew process. The receiver looks and sounds great Jason. Congratulations.
Jason wrote:
I really like the camaraderie and elmering during the process. Not to mention seeing the different builds and how people approached the design. That helped me, as I’m a visual learner. I’ve been a ham for almost 40 years and I love building rigs. This was a blast.Thanks again, Jason WV3V
------------------------------------------
For more information on how you too can build the receiver:
Herodotus once said that "learning is not child's play -- we cannot learn without pain." I think Jim KF8BOG proved that in this build. I'm sure he burned his fingers at least a few times. I remember fondly almost seeing the light buld turn on when Jim came to understand how the diode ring mixer really works. He struggled to tame a rebellious AF amplifier (we've all been there). Throughout Jim demonstrated the persistance and determination that are needed to turn a bunch of parts into a well-functioning receiver. He did it. He built it. Congratulations OM!
Jim wrote:
I am not just an appliance operator now but only half way through. Time to make a transmitter!
A little about me I became interested in Ham radio about 45 years ago in Boy Scouts I tried really hard with my Radio shack straight key and morse code chart to learn code by myself and just could never get it. Fast forward to last year and I had a friend who did CERT and he told be about it and said he used 2 meter for communications I was impressed and said “how did you learn morse code?” he replied “ I didn’t you don’t need it anymore” I promptly signed up for Ham in a day in June and got my technician license and my then my general in August. I have been studying radio ever since. This project was perfect for me. I like to make things I have been a mechanic for 40 years plus ASE master. Fixed all sorts of crazy electrical issues but DC and RF are way different lol.
Again Thanks Bill and Dean you don’t know what you have started. 73s KF8BOG
----------------------------------
For more information on how you too can build the receiver:
"SolderSmoke -- Global Adventures in Wireless Electronics" is now available as an e-book for Amazon's Kindle.
Here's the site:
http://www.amazon.com/dp/B004V9FIVW
Bill's OTHER Book (Warning: Not About Radio)
Click on the image to learn more
Where are the readers of SolderSmoke Daily News?
Pete Juliano N6QW
Master Homebrewer
Dean Souleles KK4DAS
With beret and with a Michigan Mighty Mite in hand
Re: Testing a swinging choke
-
For testing filter chokes, I tacked together a transformer, variac, diode
bridge, various load resistors (I'm lucky to have the Clarostat power
resistor de...
The Ides of March are soon to be here!
-
Leave it to my Roman ancestors to make things hard -- just look at the
Roman numeral counting system, and so it was with their calendar dates. The
Romans c...
Enjoyed the Yarra Valley Hamfest
-
Victoria seems to have a good number of hamfests and today's at Yarra
Valley was excellent. I bought a variable power supply which I hope is
lower noise th...
The Communicator March - April 2025
-
*Lots happening...*
You will find some great articles in this issue, along with our regular
columnists.
Now read in over 165 countries, this issue brings ...
40m Pelican Case SSB Transceiver
-
See YouTube channels for details:
http://www.youtube.com/c/CharlieMorrisZL2CTM
*Test code for the LCD and Si5351*
#include
...
Hollow-State Design, 3rd Edition
-
Hollow-State Design, 3rd Edition is available from: Lulu Press:
tinyurl.com/hollowstatedesign3 eBay: search for “hollow-state design”
Electric Radio bookst...
I Finally Bought My Dream Airplane
-
Aviation has been a love of mine since I was a very little person. Living
in Nevada, seeing posters and ads for the Reno Air Races, specifically the
Texa...
2000 47pF Caps ...
-
An unexpectged package arrive in the mail today. Did you ever wonder what
2000 47pF NP0 capacitors look like? Thanks to John, AB2XT I will never run ...
Daylight Again – An all Analog Radio
-
What’s all this? In 10 seconds, A high performance, 7MHz, 5 watt SSB rig
Draws just 24 mA of current 90 dB dynamic range, 80 dB close-in dynamic
range 3D ...
Digi-chirp! Digital synthesis of ‘nostalgic’ CW
-
The bottom ends of 80, 40 and 20m are not what they used to be. For
starters, the busiest part is the digital segment where computers talk to
computers – l...
Modifications to the Dayton/FDIM-2019 Antuino
-
The Dayton Antuino has sub-optimal performance. This is a short note on
improving it to an 80 db range of measurements. The trouble with Antuino
2.0 (the o...
Raduino as NBFM TX
-
Here is a neat, 30 minute hack for your Raduino to turn the Si5351 into a
pretty stable, solid NBFM transmitter. The hack is to add a varactor diode
in ...
QRP Labs shop!
-
[image: Shop]
All QRP Labs kits may be ordered online securely at the shop, with PayPal
payment.
*Click here to visit the shop!*
*Click!*
*Shop! Order...
Posts
