SolderSmoke Podcast 182: Bears! MMM Update, On Pete's Bench, 160 AM Dreams, MAILBAG

N6QW Selfie

SolderSmoke Podcast #182 is available

http://soldersmoke.com/soldersmoke182.mp3

Travelogue:  In Shenandoah with BEARS!

Michigan Mighty Mite Update and a Generous Offer (with conditions).

BENCH REPORT:

-- Pete's Ten Tec Conversion using LTSpice

-- Pete's Simple-ceiver

-- My CB to 10 conversion plans

DREAMS OF 160 METER AM:   KB3SII, N2CQR, N6QW Building for Top Band

Raspberry Pi Nightmares

Homebrew to Homebrew (HB2HB) Contacts

Elser Mathes Cup -- We have some competition!

QST, "The Radio Art,"  and The Channelization of HF Bands

WA5BDU Nick Kennedy on QSO Today  Podcast

Ed Walker of "The Big Broadcast" was a ham:  N3HFT

MAILBAG:  A Letter from Turkey: Tubes and R-390s

Si5351:  G4GXO says give it a go!

Listening UP for KIC 846

Update on a story we mentioned a few weeks ago:

Since October 16, the SETI institute has been using its Allen Telescope Array to observe KIC 846 2852 over a wide range of radio frequencies (1 to 10 GHz), looking for any artificial signals. Keep in mind that this star system is relatively far, roughly 1400 light-years away. That's more distant than the Orion Nebula, and getting there (if you feel the need) would require a 23 million year ride in our fastest rocket. But more to the point, any signals detectable here on Earth would have to be exceptionally powerful.

We're continuing to analyze the data. In another week, our SETI team will once again observe KIC 846 2852 using some new receivers being affixed to the Allen Array - known as Antonio feeds - that will increase the sensitivity by a factor of two. Check this space.

Meanwhile, consider KIC 846 2852 as something suggestive of cosmic company, but no more than a suggestion.

http://www.seti.org/seti-institute/news/alien-engineering-around-strange-star

Pete's Suggestion for My Next Rig

 

http://www.classeradio.com/

 

OR THIS:

 

http://www.ebay.com/itm/Harris-MW-1A-AM-Broadcast-Ham-Radio-Transmitter-/191739186033?hash=item2ca48bcb71:g:fx8AAOSwkZhWSR3A 

The Class E rig is very tempting.  But no way on the ebay!  Too much of an appliance -- it even looks like a refrigerator.

AM Madness: Just When You Thought It Couldn't Get any Cooler...

I pulled an old Eico 435 'scope out of retirement.  I hope to use it as a modulation monitor (any suggestions on easy ways to hook it up for this purpose?).  I really like the grey and aluminum look of this station.  I tried putting a DX-60 on the same bench, but the green of the "modern" Heathkit clashed with the serious-radio look of the DX-100 and HQ-100. Thanks again to Tim Sutton for the aluminum boxes -- I am temporarily using them as supports for the D-104 and the 'scope.  You see, I'm standing up when I modulate this gear.  Somehow it seems right.  Also, the transmissions on AM are so long that you can go back to your chair and rest (a lot!) between your transmissions.  When your turn comes, the few seconds it takes you to get to the rig provide the customary (and polite) "dragging of the feet" that allows others on the frequency to announce their presence.  Then comes what is perhaps the most fun part of this setup: the AWESOME KERCHUNK sound of the DX-100 going from receive to transmit.  As you can see, we pay a lot of attention to aesthetics and radio ergonomics here at SolderSmoke HQ.  That little blue recipe box holds my AM contact card file from the 1996-2000 period of operations from Northern Virginia.

I'm planning on doing a little work on the DX-100.   There is a standard set of mods to the audio amplifiers, mostly just changing some caps. And I need to find out why some of the crystals are not working -- I suspect dirty contacts.   I might also change the mic connector.  Looking ahead, Steve Silverman KB3SII (SolderSmoke Lex-pert), Pete Juliano N6QW and I have vague plans for an assault on 160 meter AM.  

Over the weekend this rig yielded a number of really FB contacts. Brett N2DTS in South Jersey was running an amazing homebrew station:

And Now for Something Completely Different: Boatanchors! AM! Top Band!

Lately  I found myself looking for something different to get involved in.  Pete's conversion of his Ten-Tec commercial rig got me thinking about converting an old CB rig to 10 meter AM.  I'm still planning on doing this, but noodling on this project got me thinking about AM in general.  I had the DX-100 that John Zaruba K2ZA had given me (it was his dad's).  I had it paired up with an old HQ-100 that I'd picked up in the Dominican Republic 20 years ago. (Looking at the old manual for this receiver, I realized that there is another reason why I feel so connected to it:  it was built on West 34th St. in New York City, not far from where I was born.)   On Veterans Day (November 11) I connected these two old Boatanchor veterans  to my 40 meter dipole, rigged up a connector for my Astatic D-104, and fired up on 40 meter AM. 

I had a blast!  I found myself in contact with hams who are interested in the inner workings of their gear, guys who know which end of the soldering iron to grab.  The DX-100 got great reports -- people said it sounded nice. 

Sam K4NDY told me that his DX-100 had started out at 100 pounds, but that as time passed (and as he has gotten older) he noticed that it has somehow increased in weight!   

Bill K8DBN was running a DX-60 and (like me) an HQ-100 (you see, we're no longer in Yaesu-Icom-Kenwood land!)

Mike KC2KJ was running a DX-100 and a Drake 2B.  FB!

Steve W3DEF was on with his B&W 5100B.

Dave W3CRA was on from the Collins Radio Association.  He restores Collins gear.  When he told me the DX-100 sounded great, I knew that it really did.

Today I talked to Ed KA3PTX who has this really cool Boatanchor station:

And also today I had a great contact with Howard Mills W3HM, one of the greats in the world of radio restoration.  Another fellow on frequency asked me to makes some critical comments  on Howard's signal quality ("Does he have too much low frequency?") -- I refused, saying I was unworthy. (I did say that he sounded great -- he did.)

Anyway, I'm out of the rut. An added benefit is that this new (old) interest moves me even further away from microscopic SDR rigs, and closer than ever to the Hardware Defined, analog, discrete component, menu-free radio that I prefer.  Check out the full schematic of a DX-100 -- simplicity, clarity, beauty:  

I had been thinking vaguely about someday getting on 160 meters -- I've never used those frequencies.   Yesterday I noticed that both the HQ-100 and the DX-100 cover this band.  THE RADIO GODS HAVE SPOKEN!

W2DLH's 20 meter Mighty Mite

N2CQR & N6QW,

 

I ran across a reference to the SolderSmoke book and read through it very quickly.  Through the book, I discovered the SolderSmoke podcast and have been enjoying every minute!

 

I just want to thank the two of you for the inspiration and new motivation I’ve found in a hobby I’ve loved for 25 years!  I’ve never tried homebrewing anything but that’s about to change.

 

It took me a while but we have oscillations on or about 14.060 MHz!

http://youtu.be/AUms45rwm84

I adjusted the circuit to use resistor divider biasing of the 2N2219 and changes to the biasing and coil to accommodate the 20m crystal. Also the only cap I had that worked was a 10-50pF trimmer. Aside from my placing the crystal in the wrong point in the circuit because I wasn't paying attention, this Michigan Mighty Mite needed minimal tweeting. The antenna is a 50 ohm resistor which the KX3 heard very well with its attenuator in line. 

 

Now my problem is that I listen to SolderSmoke in the car and it's bad form to take notes and drive at the same time. Also, I find myself wanting to experiment with all of the ideas from the podcast at once...  If I build your LBS in modules, Pete, then I can experiment later and swap circuits to my hearts content.

 

One question for now...where is a good source of plentiful, inexpensive crystals?

 

Thanks again, guys!

 

Darryl Hambly, W2DLH

- - - - - - - -

Grid DM78pu

G-QRP 15014
QRP ARCI 15138
SKCC 10990
- - - - - - - -http://www.qrz.com/db/W2DLH

Waco Mighty Mite Mojo!

Eric:  Wow, great news from Waco.  JOO indeed!  And I really liked the WAY you did it, liberating crystals and wire from old TVs.   That definitely adds mojo to the Waco M^3.  Bill

 

Hello Bill,

  My name is Eric Melling KD0OXY. I have, as of tonight, officially passed selection for the CLA. My Michigan Mighty Mite began oscillating tonight between 1830 and 1900 CST and I am ecstatic about it! My foray into home brewing began mid-2011 when I obtained my general class ham license (I took Technician and General at the same time taking advice from my late grandfather). The first radio I ever purchased was the Pixie II kit and boy was that frustrating. I meticulously assembled the kit and worked very hard to stuff the transceiver, volume control, options to use the on-board key or a straight key, and maybe an on-board speaker or phones.  But, to my chagrin, I was treated to the sweet wafting smell of the magic smoke long before ever getting on the air. I eventually did get on the air with my aforementioned grandfather's VHF/UHF HT and until recently, this has been the extent of my Ham career.

 

  But on the advent of my starting an MA in applied linguistics at a school in Dallas (hour and a half from home in Waco) and the rekindling of my electronics knack occurring near- simultaneously with my discovery of the SolderSmoke Podcast, I decided to give it another go. First, I got the old pixie kit to oscillate and then ripped it apart for parts to another project (non-radio). Then I procured a second Pixie kit from ebay and built that. It oscillated right away! Still no contacts; my CW is... improving.

 

  All this to say that I still had an itch that wanted scratching Enter: The Color Burst Liberation Army! Not only could I truly build something from scratch, I could follow my true calling and de oppresso liber some crystal. So I pulled some 30 (or so) gauge magnet wire from an old CRT. I had wound and rewound my coil three times (and unfortunately, the third one looks the worst) for 80m then 20m (far fewer turns) and back to 80m with N'JOO (No Joy of Oscillation) in any configuration. I am using a polyvaricon pulled form an old AM/FM transistor radio, the Mitsumi PVC-2FX which has 82 pF, 140 pF,  20 and  40 pF sections which I have wired in parallel giving me ~0-282 pF of range? And finally, I was using a MPS A42 NPN transistor. I had to run some resistors in parallel and some caps in series to get the right values, but I eventually got it all together and looking pretty smart on a 1" x 1.5" piece of perf board. Alas! Nothing!

 

  I was poking around at the circuit and realized that when I keyed the transmitter, the coil would get really hot right at the tap. I still don't know why that was, but I figured it was a good sign as it meant something was happening. I also was getting plenty of pops and clicks on the receiver. Anyway, to make a short story long, I decided that the dark mark under the transistor was a bad sign, found an NTE 123 and plugged it in instead. And oh what a wonderful day to hear the first warblings of my very first all scratch built transmitter hitting the airwaves! And here is the video: https://youtu.be/yq2M1ryMkII

  

  Probably more than you wanted to hear, but there it is. I do plan to build an SSB transceiver someday (hoping sooner than later). I feel you and Pete and your podcast have really set me out on the right foot! I hope to HB2HB with you soon!

  Sincerely,

    Eric KD0OXY