A Phasing Receiver from Montenegro (Video)

Thanks to Peter Parker VK3YE for alerting us to this beautiful receiver from Bore 4O6Z in Montenegro.  This may be our first ever report on a Montenegrin rig.  And it is a thing of beauty. Bore says it is based on a phasing circuit by homebrew legend V. Polyakov, RA3AAA.

Here is 4O6Z up on the tower:

Snowed In! Audio Mods on the Hammarlund HQ-100

It is snowing here today, so I am stuck in the hamshack.  YEA!

I've had the Hammarlund HQ-100 receiver on the bench because I am building an outboard digital frequency readout for it and for the DX-100.  More on this later.  But as long as I had it on the bench I decided to do a mod to the audio output that has LONG been needed.  

Here is a nice web page that describes the problem and the solution.  The problem is the "Auto Response audio output circuit" touted in the add up above.  Essentially I had to remove the touted circuitry.  The AutoResponseectomy only took me about 15 minutes and the results are quite noticeable.  The old receiver sounds a lot nicer.  I'm listening to 40 meter AM now.  FB.

Here is the page:

http://www.amwindow.org/tech/htm/hqaudiomods.htm

The HQ-100 does indeed have "three dimensional beauty."

"QSO Today" Podcast Interview with Michael Rainey AA1TJ

Eric 4Z1UG has a really great interview with Michael AA1TJ:

http://www.qsotoday.com/podcasts/aa1tj

I listened to it as I aligned my HQ-100 receiver and worked on a digital frequency readout for the old receiver.   The interview was the perfect accompaniment for such a project.  Inspirational stuff.  Lots of great info on QRPp and homebrewing.  Mike talks about some of his more famous rigs including the voice-powered New England Code Talker (pictured above).  

I loved the story of Michael carting his DX-100 home in a wagon.  And I really sympathized when he described the harsh reaction of the phone operator to his early efforts at voice modulation.

Strongly recommended!   You won't be disappointed.  Great interview.  Thanks to Eric and Mike.

http://www.qsotoday.com/podcasts/aa1tj 

ZL2CTM's Teensy SDR SSB Superhet -- Very Cool

Hi Bill

I thought I would drop you a quick line to show you something I have been playing around with for the past couple of weeks. It's a SSB superhet using a PJRC Teensy 3.1 microcontroller (YouTube link below), and a great audio library by Paul Stroffregen. Suffice to say I'm really happy with it.

There is a direct conversion front end, albeit using a VFO 15kHz down from the incoming RF. The 15kHz IF is then fed into the Teensy audio line in which can handle up to 22kHz. From there everything is in software. First is a 2.4kHz BPF tuned to the LSB, followed by mixer with a 15kHz BFO. Finally, there is a 2.4kHz LPF. Next step is to add both CW-wide and CW-narrow filters which can be selected during run time.

As you can tell from the video, my antenna is not the best and I have quite a bit of QRM in the shack. I really need to think about a better antenna, but that's another story.

https://youtu.be/9-rA-VAdrZA

I have been following your R2 endeavors with interest, and as I said to Pete I will attempt to replicate the R2 on a Teensy. I will try and use the divide by 2 arrangement you tried as the logic looks right.

I will also be adding in a transmitter. For that I'll use the microphone input and then take the audio from the line out straight to the RF pre/power amp. 

I must admit that I really enjoy homebrewing hardware/software hybrids as you get the best of both worlds. As i say that, I wonder how much ADCs cost these days to directly digitize RF...  Now that would be interesting.

I'll say again that I really enjoy following the podcast. I have loved electronics since I was a small boy when my parents bought me a battery, switch and light bulb. This age of cheap DDSs, microcontrollers and the like is amazing, and I get so much enjoyment putting them all together to make functioning ham radios. I hope more get into the homebrew field as the entry barrier is dropping fast.  

Keep up the good work.

73s

Charlie

ZL2CTM

A Snow Day Well-Spent: Chris Modulates an AD9850

Feb 10 at 7:40 AM
Hi Bill and Pete,
My work is closed today due to the snow so I wanted to show you what I've been up to.
I built sort of a test fixture a while back for those cheapie EBay AD9850 boards based on AD7C's DDS circuit using an Arduino Uno as a controller.
Last summer someone posted a link to Analog Devices App note AN-423 on QRP-Tech I think.
It was always on my list of things to try.
Armed with a schematic of the eBay DDS gleaned from Doug Pongrance's website, I got to work. It involved cutting a trace or two on the DDS board using an X-Acto knife.
Two outputs of the DDS chip are fed into a wideband transformer as in the app note's second page and I hung a scope probe off the secondary of the transformer.
Basically you are removing the Rset resistor on the DDS board (marked R6 on mine) and using a 2N7000 MOSFET as an electronic version variable resistor and modulating the MOSFET.
This lead to much frustration over the afternoon. No output on the scope!! Did I make an error or connect something up wrong? I was using the 600 ohm output of my HP652A audio generator. I thought about it during lunch and decided to try the 50 ohm output. Bingo!! At the 3V RMS range setting on the generator I now have some kind of signal. Not a nice sine wave shaped AM output but at least something resembling a clipped sine wave. The circuit is really touchy as far as needing a hefty audio signal in. The output of my iPhone at max volume doesn't turn on the DDS chip.
I set the DDS for 1200 kHz and can listen to it on a Radio Shack portable radio. Varying the audio generator varies the received tone on the radio just like I was expecting.
I just need to figure out what's up with the audio levels.
Chris
KD4PBJ

Feb 11 at 7:53 AM

I did manage to reduce the audio a little and get clipping to go away. I'll send another set of oscilloscope shots tonight. 

The only thing I don't get is why the audio level needs to be so high. The app note said 1 V peak to peak should be enough but I am having to drive it with 7 V p-p audio to get a decent waveform with 0.8 V p-p RF. 

I did cut the traces going to pins 12,20 and 21 to the DDS chip rather than pick up the signals elsewhere in the board. This was because once the traces go into vias down in the board, I'm not sure what else they connect to. 

Chris

Feb 11 at 1243 PM

Found the original email from May of last year about the app note. It was on the EMRFD list. After hearing you guys lately talking about AM it has me excited about an AM transmitter. 

I just got a thought over lunch that I'm going to try tonight and that is biasing the 2N7000 gate with a couple of volts to see if I can get the transistor on. Then maybe I don't need as much audio. I'll definitely put a series cap in though to my audio source so I don't fry my iPhone!!!

More to come this evening!

Chris

Feb 11 11:23 PM

I'm so excited!!

That's exactly what I needed to do-bias the gate of that 2N7000 so I'm not depending on the audio to turn it on, only to modulate it. 

I hooked up a 9v battery across a 10 k trim pot and connected the wiper to the gate of the fet. A 10 uF cap is in series with my audio line as not to feed DC back into my source. 

I have audio and now the output of a small radio or iPhone modulates it fine. 

So this is a great proof of concept! Those cheapie DDS modules from China can be AM modulated. 

I need a mic amp now, filter (surgery to the board disabled the on board LPF, but yes Steve I'll install one right away), buffer amp and some kind of linear RF amp to get a few watts. 

Chris 

Here's a video of Chris's project:

 

 

Gravitational Waves, A GREAT VIDEO, Phasing, and Joe Taylor K1JT

Wow, you really have to spend 20 minutes and watch the video (above).  It is really well done.  I loved it.  I give it FIVE SOLDERING IRONS!

And big news today!  They did it!  Gravitational waves finally detected.  Here is a good New York Times article that includes a recording of the signal, a nice NYT video that has a good explanation (with phasing!) of how lasers are used in the massive detectors, and mention of Joe Taylor, K1JT, whose Nobel Prize winning work contributed to this great discovery.

http://www.nytimes.com/2016/02/12/science/ligo-gravitational-waves-black-holes-einstein.html?partner=rss&emc=rss&_r=0

Life in the Fast Lane: Potato Semiconductor Chips

Even I, with my luddite tendencies and analog preferences, have recently bumped up against the speed limit of 74 series logic chips.  The Si5351 chip in the I and Q VFO for my phasing receiver will run up to 160 MHz.   But the 74 series inverters and flip flops that I have attached to the output don't seem to want to go beyond about 120 MHz.   Our old friend Thomas LA3PNA tells us how to break this speed limit:

http://www.potatosemi.com/  

Be sure to go their "Milestones of 74 Series Logic" Page.

I like their explanation of the brand name: