Just go to http://soldersmoke.com. On that archive page, just click on the blue hyperlinks and your audio player should play that episode.
http://soldersmoke.com
I'm guessing that most of you have never listened to a regen receiver that uses only one transistor. So in these videos I've tried to capture the experience. The audio that you hear from the receiver is from a small I-phone microphone taped to the one of the headphones on my DLR WWII headphones. So you are hearing it just as I hear it -- with no additional amplification. Here is N0WVA's schematic. When I tune the "regeneration" control I am turning the knob on the variometer. The broad or "bandset" tuning control is essentially N0WVA's 25 pf cap. My fine tuning control (the one that I use the most in the video) is the equivalent of the smaller cap in parallel with the larger tuning cap.
I had trouble shooting the video for this post -- taping the mic to the headphone turned out to be a bit difficult. So I ended up with a few extra (and imperfect) videos. I include them here for anyone who might want to listen some more to a single transistor regen. (I have a few more -- let me know if you'd like to see them!)
In the next one, at the end I throw the switch to transmit allowing you to hear what "sidetone" sounds like on the ET-2
Thanks for posting the demo, I'm impressed! Good to hear after listening about it in the podcast. 73 de Walter, AC4IM... still in Italy at the San Vito solar observatory.
I was wondering what you were using for the sidetone. I see it is the "receiver blocking" method. :)
Spotting your transmit signal is probably the largest hurdle to overcome with a regen. It may be possible with total shielding and clean antenna switching, but that takes away from the nostalgia of an open air station. Could you imagine doing this without crystal control? Imagine basically four free running oscillators all trying to stay close to each others frequency as the table vibrated and power supply voltage ramped up and down. Dont breath on the tank circuit!
Re Anon, there are techniques that don't require you to spot your tx signal on a regen. For example you could have a second tx crystal with its frequency shifted 800 Hz (eg VXO) from the crystal in the tx. That second tx crystal could be in an oscillator running all the time to provide a BFO for the regen rx. The regen rx would be brought to the point of oscillation but not oscillating. There's some 1930s(?) QST articles about the merits of a separate BFO for regens.
Alternative you could configure your tx so the local osc is running all the time and have that as your BFO for the rx. But you will need to shift it 800 Hz to get an offset. That could even be done manually eg with a variable capacitor in series (and an inductor if you want more VXO range).
Another thing that could be useful is putting a tx crystal in the antenna lead of the regen - that will act as a crude xtal filter. You might hear an interesting change in noise as you adjust the rx to near that frequency.
"SolderSmoke -- Global Adventures in Wireless Electronics" is now available as an e-book for Amazon's Kindle.
Here's the site:
http://www.amazon.com/dp/B004V9FIVW
International sounds for the umbraphiles
-
Hi I’m FastRadioBurst 23 from the Imaginary Stations crew letting you know
about this week’s shows. The first broadcast is to Europe via Shortwave
Gold on...
Replies from the Ergonomics vs. Performance poll
-
Yesterday, I posed the following question and asked for your input: “Which
aspect of a QRP radio holds more importance for you: its ergonomics (ease
of use...
March 28, 2024. Just another Day at the Office.
-
FT-8 with a RPi Zero W
Given the FT-8 achievement maybe even QUISK would work on the RPi Zero W
for a really small SDR Transceiver.
But all that g...
The GM3OXX “Oxo” Transmitter
-
As well as the small stash of finished projects that grace my living space,
I also have two small boxes containing various boards. Some of them are
boards ...
Handy breakout board for Raspberry Pi Pico
-
Just picked up a few of these breakout boards. I'm not sure that I like the
screw terminals but it is handy having LEDs on each GPIO pin. I'm really
gettin...
Repairing a dead Kenwood TS-850S
-
Recently, a Kenwood TS-850S - a radio from the mid-early 1990s - crossed my
workbench. While I'm not in the "repair business", I *do* fix my own
radios,...
A 51S-1 Restoration Story
-
I came across my Collins 51S-1 in a big junkyard in Ankara, Turkey around
2012. It was in a pile with a lot of other electronic scrap, probably from
one o...
New QRP Cluster Online From OM0ET and OM6APN
-
By DX EXPLORER
DX EXPLORER
Paul OM0ET and Peter OM6APN recently launched a new cluster dedicated to
QRP operations. Have a look and I hope you will enjoy...
3D Printing The Hadley 114mm Newtonian Telescope
-
Yes, we’re building a 3D Printed Newtonian Telescope called Hadley. It’s
being printed in PETG and in the video below, I give a quick tour. My build
isn’...
3D printed project boxes
-
I have been busy with some other things that have kept me away from
electronics projects for quite a while. Now I can get back to them, but
realize I n...
Daylight Again – An all Analog Radio
-
What’s all this? In 10 seconds, A high performance, 7MHz, 5 watt SSB rig
Draws just 24 mA of current 90 dB dynamic range, 80 dB close-in dynamic
range 3D ...
Adding Enclosure to your sBitx Boards Order
-
The early buyers of the sBitx board set who bought it for $270 USD might
want to also add the enclosure (box) for in the kit. What you will now get
is a f...
Digi-chirp! Digital synthesis of ‘nostalgic’ CW
-
The bottom ends of 80, 40 and 20m are not what they used to be. For
starters, the busiest part is the digital segment where computers talk to
computers – l...
-
A Simple Speech Processor
(For QRP/SSB Homebrew Transceivers )
Over the last few weeks I had been thinking to build a small AF speech
processor to add to...
A New Look for your uBitx!
-
Adding a "Cool Blue" Display to your uBitx!
The standard "green background" with black lettering frequently reminds me
that I suffer from Chronic seasickn...
Thanks for posting the demo, I'm impressed! Good to hear after listening about it in the podcast. 73 de Walter, AC4IM... still in Italy at the San Vito solar observatory.
ReplyDeleteI was wondering what you were using for the sidetone. I see it is the "receiver blocking" method. :)
ReplyDeleteSpotting your transmit signal is probably the largest hurdle to overcome with a regen. It may be possible with total shielding and clean antenna switching, but that takes away from the nostalgia of an open air station. Could you imagine doing this without crystal control? Imagine basically four free running oscillators all trying to stay close to each others frequency as the table vibrated and power supply voltage ramped up and down. Dont breath on the tank circuit!
Doug N0WVA
I Love your minimalist leanings, and CW. FB! Keep soldering! Ed KC8SBV
ReplyDeleteRe Anon, there are techniques that don't require you to spot your tx signal on a regen. For example you could have a second tx crystal with its frequency shifted 800 Hz (eg VXO) from the crystal in the tx. That second tx crystal could be in an oscillator running all the time to provide a BFO for the regen rx. The regen rx would be brought to the point of oscillation but not oscillating. There's some 1930s(?) QST articles about the merits of a separate BFO for regens.
ReplyDeleteAlternative you could configure your tx so the local osc is running all the time and have that as your BFO for the rx. But you will need to shift it 800 Hz to get an offset. That could even be done manually eg with a variable capacitor in series (and an inductor if you want more VXO range).
Another thing that could be useful is putting a tx crystal in the antenna lead of the regen - that will act as a crude xtal filter. You might hear an interesting change in noise as you adjust the rx to near that frequency.
ReplyDeleteThis comment has been removed by a blog administrator.
ReplyDelete