A Slovakian Al-Fresco Digi-Tia Homebrewed In France (and an improved AD9850 VFO)

Hello Bill and Pete,

Thanks for the podcast! My normal occupation is more computers and
software but your podcast got me motivated to melt some solder. So I
want to share a bit of what has been cooking on my bench.

I used to have a Yaesu FT-450 but sold it - I am living in a tiny rental
apartment in France without any place where to put a proper antenna so
it was only collecting dust. And where is the fun in operating a
factory-made rig, right?

So I have been working on this instead:

http://janoc.rd-h.com/archives/541

This "al fresco" rig is "half-DigiTIA". Half because there is no
transmitter part (I don't have a French license and I am too lazy to do
the paperwork and convert my Slovak one).  The purple modules are TIAs,
as designed by Wes Hayward, using 3x 2n3904s, only built using SMD
components to keep them small and tidy.

VFO & BFO are Si5351 + ATMega328, with an OLED module and code adapted
from Pete N6QW. It uses 11.997450 MHz IF because that's where most of my
12MHz crystals actually matched.

The 40m bandpass filter is taken verbatim from the BitX 40 design - I
have only changed the coils to use toroids instead.

For audio I have used LM386 with a NE5532 opamp as a low noise preamp
because the audio was a bit low. The TIAs don't have a lot of gain and I
have only an indoor magnetic loop for antenna so had to compensate for it.
I have another, a bit older project that became quite popular - firmware
for the AD9850 DDS VFOs using an Arduino and a character LCD. It is a
much improved replacement for the one from Richard, AD7C.

http://janoc.rd-h.com/archives/502

Perhaps it could be useful to someone.

Keep up the good work and 73!

Jan OM2ATC (at the moment "in exile" in France)

N8NM's SR-16 Hallicrafters Tribute RIg

Bill,  Pete:

The rig is loosely based on the Hallicrafters SR-160 transceiver, since I'm using a RD16HHF1 in the final RF, I'm calling it the SR-16.   It's a tri-band rig covering 80, 40 and 20m.  Architectually, it's similar to Pete's JBOM, which is partially coincidental (thanks for sharing the article, Pete!)  The heart of the rig is the W7ZOI hybrid-cascode IF, a really slick circuit that really makes the rig a joy to use. 

Frequency generation is handled by the ubiquitous Arduino/Si5351 combo and a sketch based on Tom, AK2B's "Multi Function VFO", to which I added functions for selecting the appropriate bandpass and IF filters, generating CW, RIT, and dual VFOs (with split functionality), the state of which is saved in EEPROM when the rig is powered-down.

The rig's just about finished - I've got the remaining parts ordered and hope to have it on-the-air soon.

73! - Steve N8NM

From Mountaineer to the KX1 -- N6KR on Trail-Friendly Rigs

This is from 2014, but I stumbled upon Wayne Burdick's article just this morning.  Great stuff.  That picture of Wes had a big impact on many of us. 

Wayne's article:

http://www.elecraft.com/KX1/N6KR_KX1_History.html

SolderSmoke Podcast #191 RIGS! REAL RIGS!, BITX40 Module, EMRFD, MAILBAG

SolderSmoke Podcast #191 is available:

http://soldersmoke.com/soldersmoke191.mp3

TRAVELOGUE AND FAMILY DOINGS:   Pete son's wedding, Billy's Birthday, Gonzalo safely home in the Dominican Republic, MORE BEARS IN THE SHENANDOAH WOODS

BIG NEWS:  EMRFD LIVES ON!   Three cheers for Wes and for Tom Gallagher of the ARRL.

BENCH REPORTS:

PETE:   FPM Rig.  Some Halli history.  A TRUE RIG!  Working Japan. 

             WITH 600 WATT LINEAR AMPLIFIER!!!!!!!!!!!!!!!!!!!!!!

               New FEELTECH  Sig Gen.  

BILL: Farhan's BITX Module

           Built to Mod, built to get you started in homebrew

           Very impressive.  BITX in miniature.  But completely recognizable.

           REMARKABLY stable.

           Farhan personally checking each one.

           Ladies collective doing toroids.  DONATION money bought them some Diwali candies!

           VFO Drift:  Will NP0 SMD caps and lower current help enough?

           My Analog VFO -- BANDSWEEP

QRPppppppppppp  with REX's Hamfest Buddy.   Thanks Rex and Bob Crane.

HB2HB with KW4KD

MAILBAG

Jan's Netherland Mate Mighty Midget

Charlie's Kiwi DSB

Steve, Donald Fagan, and Jean Shepherd

Rob VK5RC repairs Tek Tube 'scopes

Colin M1BUU Si5351 superhet

Denis Klipa and NRL 3538

Jonathan M0JGH Wizard of Wimbledon Matchbox rig

JH8SST Simpleceiver

Peter Parker Vk3YE Reviews Book

Peter GW4ZUA Welsh LBS

Michael Rainey helping hobbyist in Germany with tuning forks.

Hacking the Hackable BITX 40 Module: VFO is the Way to Go!

I am having a lot of fun with Farhan's new BITX 40 Module.  I think I'm doing exactly what Farhan intended people to do with this rig:  work on it, modify it, improve it. 

I've been working on frequency stability.  I was, I admit, skeptical from the start about the stability of a  thumb-sized,  SMD, varactor-tuned VFO with a ferrite or iron powder toroidal coil.  Don't get me wrong -- it worked.  But it drifted. It seems to me that it would be asking too much to expect a VFO like this to be drift-free. (But I may be wrong -- are there any SMD, varactor-tuned VFOs out there that DON'T drift?)

First I thought it might be the 9 uH metallic core toroid.  So I replaced that with a 10uH choke -- no ferrite or iron powder in there.  That seemed to help a bit, but SSB QSOs would still quickly drift into Donald Duck chatter.  Then I thought it might be the varactor diode.  I let it warm up.  A lot.  Still, it drifted.  Then I thought it might be the trimmer cap, so I took it off the board.  No change.  During this process I noticed that even slight pressure on the board caused the rig to shift frequency.  I began to suspect that the drift was just structural -- a consequence of the physical characteristics of the SMD parts and the board.  To get VFOs stable I've had to build them big:  10 X 10pf  NP0 caps to make one 100 pf cap, large air-core coils, and big sturdy variable caps.  I'd isolate the frequency determining elements in a box separate from the powered components. This little VFO just looked too small to be stable.   

So faced with drift, at first I asked myself,  "What would Pete do?" I took an AD9850/Arduino combination off the shelf and plugged the output into the "DDS" jack Farhan had placed on the board.  I removed the 10uH choke.  Viola! With the DDS tuned to 4.7 - 5 MHz, the receiver worked great.  I briefly tried to updated the Arduino code to take into account the 12 MHz IF (so I could get an accurate frequency readout), but ran into the old painful Arduino IDE problems:  Now it is claiming there are library problems.  Not wanting to suffer through another round of digi-agony, I left well-enough alone.   I used the DDS with the old code for one day. 

But of course, I was not satisfied.  Attaching a DDS or PLL synthesizer to the BITX 40 Module just didn't seem right. Heck, it was kind of like just hooking up my FeelTech Chinese sig gen to the DDS jack.  Farhan's rig is simple, beautiful and ANALOG.  The parts are small, but you can see them.  You can put your scope probe on the collector of Q7 and see what is going on.  DDS or PLL.  It is a REAL HARDWARE-DEFINED RIG.  So I decided to build a VFO.   Pete calls VFO's "grief machines"  but for me, the grief machines are those little Arduino beasts.  To each his own.

When I build a VFO, I start with the variable capacitor and the reduction drive.  I found a nice one (with reduction drive) in my junk box. I tunes from 40 pf to 56 pf.   I decided to use the super-simple Hartley circuit presented by Wes Hayward W7ZOI in SSDRA (page 34, fig 7). 

I went with a 4.4 uH air core coil (wound on a cardboard tube from a coat hanger).  Consultation with on-line resonant frequency calculators showed that I'd need to put about 180 pf in parallel with the variable cap.  For this, I used a bunch (maybe 10?) of small value  NP0 caps in parallel.  This really helps keep the VFO stable.

As I did with my HROish receiver, I put the coil and the caps in one box, with the MPF-102 and associated parts in an  attached Altoids tin.  Everything was glued and bolted down very solidly.

I only built the actual oscillator stage -- I decided to use the buffer amps on Farhan's board.

The oscillator started right up.  I had to add and then take away some turns on the coil to get it to run in the desired range.  Then I plugged it into the DDS jack -- the receiver was working immediately.

I noticed, however, that it seemed a bit less sensitive than it had been with the AD9850 DDS. And when I grabbed the wire going into the DDS connector, audio output jumped dramatically.  It took me a few minutes to figure that out:  I think the output from my VFO was not adequately turning on the diodes in the diode ring.  When I grabbed the wire, I was putting a lot of noise into the mixer port, probably turning the diodes more fully on (but also letting a lot of noise through).

Fixing this problem part was fun:   Looking at the BITX 40 schematic, I saw that the two 1000pf feedback caps in the original oscillator were still in the circuit.  I figured those caps would be sending a lot of my VFO energy to ground.  So I fired up my hot air rework station and deftly removed C91, the 1000 pf cap that is connected to the base of  Q9.   Instantly the receiver started inhaling as it had with the DDS VFO.  That was a very satisfying fix.

This whole VFO project was very satisfying.  It was all done in one day, and all the parts came out of my junk box. I think I ended up with an LO frequency source that matches up in a pleasing way with the analog circuitry in Farhan's rig.  And here is bonus that I think is just what Farhan had in mind:  this kind of circuit adds a definite homebrew element to the module rig.   

I found that this external VFO improved stability significantly.  I don't know if it is as stable as the DDS, but with the external VFO the receiver no longer drifts away as I listen to SSB signals. 

N7UN Talks About Summits on the Air (FDIM Interview by Bob Crane)

Bob Crane, our intrepid correspondent at the Dayton Hamvention talked to Guy N7UN (pictured above) about taking ham radio up to the mountaintops.  It was nice to hear Guy mention Wayne Burdick and Wes Hayward and WG0AT.    Thanks Bob!  Thanks Guy!

Listen here:

http://soldersmoke.com/N7UN.mp3

More on N7UN here:

http://www.n7un.com/

Possibly the Best Ham Radio Interview Ever: Farhan on "QSO Today"

Stop what you are doing.  Run -- don't walk -- to the "QSO Today" website of Eric Guth 4Z1UG.   There you will find his interview with Ashhar Farhan VU2ESE. 

There is so much great information, inspiration and wisdom in this interview.  I was so captivated by it that -- even with the availability of the pause button -- I was unable stop listening even for the time it would take to walk to the kitchen to refill my coffee cup.  But at the same time, listening to Farhan describe the joy of bringing a new receiver into operation compelled me to go over to the bench -- in mid-podcast -- to tweak a receiver that I am working on.

In this podcast you will hear about how Farhan got started in ham radio, about his Elmers about the origins of the BITX, about the Minima and the new HF-1 rig, about Farhan's spectrum analyzer project and about a new goodwill effort to send BITX circuitry to aspiring hams around the world, especially in developing countries.

Throughout you will hear Farhan speak of the importance of the book, Experimental Methods in RF Design. 

I really do think this is the best ham radio interview I have ever heard.  Congratulations and thanks to Eric and Farhan.

Here is the link:

http://www.qsotoday.com/podcasts/vu2ese

Breadboarding and Mountaintopping

We needed an illustration today.  I was having trouble finding something suitable.  Then the Radio Gods (along with Joe Peltola and the artist N0UJR) provided this.  Obviously I can relate to the breadboard operation. I'm sure Pete can too.  As for the mountain topping, that made me think of Colin, M1BUU.  And of Wes, W7ZOI.

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Video of Pete's VERY COOL Zia Build

This is cool in so many ways:

I like the RF amp along the back with the LP filter off to the side.

The stacked PC boards are very nice.

The Display -- What can I say?

Having stations from the Philippines (DU) for the receiver demo.  Nice touch.

Mesh-like side panels!  And the plexiglass top!  Wow!

PAINTING THE COPPER-CLAD FRONT PANEL BLACK!  WOW!  BLACK IS THE NEW COPPER!

Nice feet for the rig.  Feet are key.

NO NOTICEABLE PHASE NOISE.  No Si5351 output bleed-over.

Love the name:  ZIA!!  (That was my only contribution.)

SolderSmoke Podcast 177 Bicoastal Termination Insensitivity Unphased by Phase Noise

 

SolderSmoke Podcast #177 is available:

 

http://soldersmoke.com/soldersmoke177.mp3

 

13 June 2015

 

-- PETE JULIANO INDUCTED INTO THE QRP HALL OF FAME

-- Bench Reports:  Bicoastal Bilateral Success:  A Tale of Two Tias

    Only 3 TIA rigs in the world?  It depends...

    Relay improvements in the BITX Builds

    Straightening out amp problems

    The many uses of copper foil

    No phase noise or bleed-over troubles

    Plug-in filters

    Adjusting TIA amp gain on RX and TX (too much is not good!)

    Getting the BITX to work with the CCI amp

    Allison wisely prescribes 3 db pads 

    Curing hum by moving the power supply (duh!)

-- Farhan's New Minima -- Crying out for an Si5351?

-- Mike KL7R's Web Site is Back (thanks to W8NSA)

-- SolderLex: Rigs or Radios?  We go with Rigs

-- A ham rite of passage:  Build a Dipole!

-- What does your shack look like at the end of a project?

-- MAILBAG 

    The CORRECT pronunciation of Belthorn

    Multiplication and Division by 4

    W8NSA, Vietnam, a Transoceanic and a 9V Battery 



 

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Termination Insensitivity -- Only Three TIAs in the World?

Termination Insensitivity.  Is this like when your girlfriend dumps you and you just don't care? 

No. It's more like this:

http://www.n6qw.com/TIA.html

Wes Hayward and Bob Kopski developed the Termination Insensitive Amplifier circuit back in 2009.  With a bidirectional rig it is important that the crystal filter face the same impedance in both directions.  Simpler bidirectional amps are impedance "transparent" in that their input impedance depends on what is on the output (and vice versa).  The circuit that Wes and Bob developed solved this problem:  these amps always look like 50 ohms.  That's very useful.  When I was building my earlier BITX rigs, Farhan suggested that I try the termination insensitive amp circuits.  On my latest project I followed his suggestion.  At the same time, Pete was building a new BITX, also using the TIA amps. 

Pete wrote to Wes and Bob and asked if anyone had followed through on their 2009 article by building a rig using this circuit.  Wes said that he was unaware of any TIA rigs.  It turned out that Tom Hall up in New York City had built one (video below). So I guess Pete's rig is TIA 2 and mine is TIA 3!  (But I was thinking, because of Pete's Italian ancestry, shouldn't we call his rig a Zia?)
Please let us know if you know of any other TIAS (or ZIAS!) out there.

Here is Tom Hall's very FB TIA:



Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

BITX DIGI-TIA Build Update #7: On The Air!

 

With lots of encouragement from Pete, I finally got the BITX DIGI-TIA on the air.  The first contacts were made yesterday. I have it on 40 meter SSB.  The finicky denizens of that audio-conscious band seemed to like the sound of the rig.   I was almost reluctant to tell them it is homebrew (no need to stir up trouble!)

 

The plug in filter arrangement seems to work very well.  This will allow me to put this rig on many other bands.  All I have to do is build some additional filter boards and upload modified versions of the software.  There is even space to make a plug-on socket for the crystal filter (the 9 MHz IF would not be cool for 17 meters).  

 

I'm really pleased with the RF power chain (the original BITX chain).  This time I built it all in a straight line along the back of the transceiver with lots of attention to shielding and grounding.  There were no instability problems.  The amplifiers did not try to be oscillators.  I was shocked!

 

I did have to reduce the gain of the three termination insensitive transmit amplifiers. Using the chart in the 2009 Wes Hayward/Bob Kopski article,  with just a few resistors you can set the gain.   I had built them with 19.4 db gain each.  This turned out to be too much -- the slightest amount of audio into the SBL-1 was driving the amplifiers to peak output.  So yesterday I changed all three amps to 15 db (I think that was what Farhan had in the original BITX).  It only took me about 15 minutes and it seemed to take care of the problem.  I am getting 7 or 8 watts out of the IRF-510.

 

T/R switching is very smooth and quiet using just two small 12V relays.

 

Thanks to Pete for the mil-pad boards and the encouragement (especially on the use of the Si5351).  Thanks to Farhan for the BITX architecture. Thanks to Steve Smith for the Yaesu filter.  Thanks to Wes and Bob for the TIA circuit.  Thanks to Thomas in Norway for the Si5351 software.  And Thanks to Allison for all the good advice.



 

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

BITX DIGI-TIA Update #4

 

Lots of progress over the long weekend.  Along the back you can see the three stages of the RF amplifier chain:  2N3904, 2N2218A, IRF510. I intend to add inter-stage shielding, and one long shield between the chain and the rest of the rig.   Front and center is the Si5351 board (code by LA3PNA).  Mic amp (which gave me a lot of trouble!) is to the right of the Si5351.   AF (RX) amp is to the left (2N3904 and LM386).  The big board in the center has the three Termination Insensitive Amplifiers (thanks Wes and Bob), the 9 MHz filter (thanks Steve Smith!) and the two SBL-1 mixers (thanks to Pete Juliano for the "mil-pad " boards).  And thanks to Farhan for the overall BITX concept and the TIA suggestion.  

 

In the upper right you will see where the plug-in low-pass filter will plug in (a better picture appears below).   I will use a similar plug-in for the band-pass filter.   Combined with the BFO/VFO flexibility of the Si5351, this plug in feature should allow me to cover many bands with this rig.    

 

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

SolderSmoke Podcast 176: Knack-Related Conditions: Termination Insensitivity, Sideband Inversion, Dongle Modification, Area 5351 Conspiracy Disorder

SolderSmoke Podcast #176 is available! (And it is GOOD!)

http://soldersmoke.com/soldersmoke176.mp3

16 May 2015

Bench Update:
Pete releases some magic (amplifier) smoke
Pete's new termination-insensitive transceiver makes first contact
Bill goes Yaesu (well, just a filter)
Juliano Mill-Pad boards
Termination Insensitivity is not a personality disorder!
Flip those Bilat Boards!  Pete's cool technique for bilat building
Bill's project notebook and stage testing
Installing the W6JFR EMRFD SBL-1 Bal-Mod Mod

AREA 5351:  Myths, Urban Legends, and Conspiracy Theories about the Si5351

A Rule of Thumb for Sideband Inversion

Dongle Madness and the Dangers of Dongle Modification
What is a dongle?
24 Mhz to 1.7 GHz right out of the box
Modification for 0-29 MHz
Tapping the IF of a Drake 2-B
Getting another one for VHF-UHF
Dongling Meteors, Satellites and Airplanes

SPRAT cover AD9850 in 1988!  Three cheers for SPRAT (and QQ and QST).

Elecraft's new Rig

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

BITX DIGI-TIA Build Update #2 Installing and Testing Yaesu SSB Filter

Termination Insensitivity.  It sounds like some sort of psychological problem, but it is not!

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

BITX DIGI-TIA Build Update #1 Building the First 2 TIA Amplifiers

I started building the new transceiver today.   I am tentatively calling it the BITX DIGI-TIA.  Digi because it will have at its heart an Si5351 for BFO and VFO signal generation, and TIA because it will use Termination Insensitive Amplifiers (TIAs).  These TIA amps are designed to present a 50 ohm impedance not matter what impedance you connect to the other end.  This is a very useful feature when you are trying to get a certain impedance for a crystal filter in a bidirectional rig -- you want the same termination impedances in  both directions.

 

I built the "top" halves of two of the TIAs, using CNC-cut boards given to me by Pete Juliano.  Thanks Pete!  I like the boards, and I no longer have a thick coating of dried SuperGlue on my fingers.

 

Both amps seem to be performing  very well. Some numbers:

 

Current draw at 12 V (no signal) 30 ma.

 

Gain at 9 MHz (no load):  Amp 1:  27.2 db    Amp 2: 26.5 db.

 

I then took a 110 ohm load and put it across the output of Amp 1.  Gain dropped to 23.9 db (as you'd expect).  BUT HERE'S THE GOOD PART:  The input voltage from my homebrew sig generator stayed exactly the same.    Termination insensitivity. 

 

More on these amps (with a link to Wes's article) here:

 

http://soldersmoke.blogspot.com/2015/04/termination-insensitive-bitx-amps.html 

 

Next  I'll put the 9 MHz filter between these amps and measure the shape of the filter passband.

 



 

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

IF Selection -- Which Filter for the New Rig?

With some prodding from Pete Juliano, I am moving forward on my next transceiver.  Same wood box enclosure (with copper flashing), but this time I am greatly relaxing some of the radical fundamentalist restrictions:  Chips will be allowed. VFOs and VXOs will be replaced by an Si5351. Filters will not have to be homebrew.  Pete has been putting his CNC machine to use and making me some nice boards with isolation pads already milled in.  Oh, the luxury!

I am going to use the Termination Insensitive Amplifiers designed by Wes Hayward and Bob Kopski back in 2009.  These are especially useful in bilateral type transceivers because they allow you to nail down the termination impedances on the crystal filter IN BOTH DIRECTIONS.   That's is important if you want the same filter shape on both transmit and receive.

But now, with the trauma of my unfortunate IF selection on the BITX 20/40 (now just 20, sniff...) in mind,  what filter should I use on this rig?  The three main candidates appear above.   The 9 MHz Yaesu filter was given to me some time ago by Steve "Snort Rosin" Smith.   The Heath filter (3.395 MHz) and the larger silver one (2.215 MHz) were given to me by Armand Hamel. (Thanks Guys!)

My main band of interest for this rig is 40.   But if possible, I'd like to be able to use it on 15 and 12 meters,  and maybe even 20 and 17,  hopefully without having to change filters. 

 So what say the gurus?  Which one should I use?   Or should I put two of them in there, with provisions that would make it easy for me to move from one to the other? 

Right now my inclination is to go with the 9 MHz filter, perhaps with the 3.395 MHz filter also available.


Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Termination Insensitive BITX Amps

 Back in 2009 Wes Hayward and Bob Kopski designed a termination insensitive amplifier block for use in BITX-like transceivers. Farhan urged me to use it.  The advantage of this design is that the input impedance stays at 50 ohms no matter what you hang off the other end.  That's very helpful, especially when you start trying to get specific impedances at the ends of crystal filters.   I'm planning on using this circuit in my next BITX.   This morning I was playing around with it in LTSPICE.  The "mirror" feature in that program is quite helpful when you are working on circuits like this!

Here is the article by Wes and Bob that describes this great circuit:
http://w7zoi.net/bidirectional_matched_amplifier.pdf

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Homebrew Heroes at Rickreal Hamfest: W7ZOI and WA7MLH

Bob N7SUR was getting discouraged.  The hams at the Rickreal Hamfest didn't seem really interested in his display about homebrewing.  Then THE RADIO GODS INTERVENED! (thunder).   Two TITANS of homebrew appeared at Bob's table.   Keep up the good work Bob,  Thanks for the e-mail and the great picture of you with Wes and Jeff.  

To N2CQR, N6QW

Feb 15 2015

The Salem, Oregon, Repeater Association puts on two hamfests each year
at Rickreal.  This event was mentioned in SolderSmoke #78.  During the
last two events I’ve taken a “science project” display and circuit
boards to encourage more hams to experiment.  The boards encourage
experimenters to use software packages to design and build their own
receiver modules.  It is uncommon to see this type of material at the
event.

Audience interest has been underwhelming.  Perhaps a dozen participants
have shown interest in my displays.  In fact, I almost left the displays
home last Saturday.

In the course of the morning, two guys approached.  The older guy had a look of
familiarity.  He looked like a guy in the SolderSmoke blog.  Bill,
N2CQR, was pictured sitting with him in California over coffee.

I blurted out, “are you ZOI?”  He replied “yes” and I told Wes Hayward,
W7ZOI, it was nice to meet him.  (That was a bit of understatement).
With Wes was Jeff Damm, WA7MLH, who built many of the circuits included
in the book “Solid State Design.”  I suggested to Jeff he no longer
looked like a hippie, which is the style conveyed by his webpage.  Jeff
said he had recently cut his hair.

We spent more than an hour sharing ideas and discussing various topics.
My focus was on encouraging experimentation.  Kit building may be a nice
first step.  I want to see builders pursuing more advanced
investigations. Wes noted the software and simulation tools available
for free it’s never been a better time to try out ideas.  Wes commented
on the contribution of amateurs and how we often have fewer restrictions
to pursuing our interests.  He emphasized measurement tools.  I should
look more at noise figure in my receiver experiments. He was very
supportive, which contrasts with my recent experiences on various
internet groups.

Wes and Jeff were looking for Rick Campbell, KK7B, and Bob Larkin,
W7PUA.  Imagine, the three authors of Experimental Methods in RF Design
(EMRFD) frequenting a little hamfest in rural Oregon. Yet, few people
knew they were there.

The experience reinforced my interest in continued experimentation.
I’ll take my updated displays back next time.  Perhaps our efforts reach
a larger audience than we first realize. 

Bob-N7SUR

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Kansas Mighty Mite

Greetings Bill

I have been a bit ill,  but finally found some time to work on my Meara Mighty Mite, which i wish to call it as it was by the grace of Bill Meara that I am able to play a part in the Colorburst Revolution could begin.

I just wanted to share some pictures from the bench of my progress, which is not yet fit for the ether.

I originally wanted to build a really unique design. I have a tendency to complicate things. The more simple it is, the more complicated I tend to make it. After a lot ambitious failed starts, I decided that the best thing to do is to keep it simple. In fact, I would say that I was "over-noodling" this one. So I just started building.

I use copper clad PCB, which I get for very cheap from an ebay seller named abcfab. I use a tool I made to cut islands by hand. Information can be found about this method on my blog.

I am almost embarrassed to share photos of my build, especially after seeing such wonderful designs as you have featured on the webpage. But the excitement is just to great, so here it goes:

I build ugly circuits and I'm proud of it.

I haven't build the LPF yet and wouldn't put it on the air without one. 

Thanks for all the great inspiration and for inspiring a revolution of colorburst liberation!

I want to share something from Solid State Design for the Radio Amateur, W7ZOI & W1FB, page 19

"All of the circuits shown are aimed at reasonable stability, but have relatively low output power. It is possible to bias many of these circuits higher to obtain outputs of up to perhaps 1/4 watt. However, thermal stability is often severely degraded, chirp is introduced if the oscillator is keyed, and the user stands a chance of damaging the crystal from excessive rf current. It is not recommended that a single oscillator stage be used as a simple transmitter. The addition of an amplifier is so straightforward, and the system efficiency is so much better, that the minimal simplicity is not of value."

That may be true, but the Mighty Mite is for learning and getting our feet wet. Still it may be interesting to point the above out or talk about it.

Also, I'm curious to know which schematics everyone is using. The famous Easy QRP transmitter on the QSL page, perhaps DeMaw's from QRP notebook (available on archive.org in pdf form for free).

73, keep your iron hot and stay fluxy,

-KE0BFF, Lawrence KS.

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20