Steve "Snort Rosin" Smith sent me this very creative reminder that the Sputnik Replica On-The-Air event is scheduled to continue for the same length of time that the original transmitter was on the air. That means we have until October 26 to work or to listen to these magnificent replica rigs. (Hey, maybe I'll get my HW-7 into the action!) See you on 21.060 MHz Comrades! 73 and DSW! 
Doug, W8NFT, sent me this booklet and copies of the recordings that came with it. Below you will find links to the booklet itself and the two mp3 files. Note that the signals were captured using an HRO receiver. Side A is a "re-creation" of the launch ("spine tingling in its realism!!!!") Side B is an actual recording of the sat's iconic beeping. 
I think Jos's rig is magnificent. He is getting the high voltage for the tubes from a cheap (3 Euros!) 12 Volt to 120 Volt DC/DC inverter that he picked up via e-bay. (I think you can see the inverter board to the left of the headphone jack.) He runs it from a 12 volt gel cell. The little battery is for the filaments. He gets about 700 mw out, and had a very solid 15 minute QSO with Jim, W1PID yesterday. FB Jos!
Our book: "SolderSmoke -- Global Adventures in Wireless Electronics"http://soldersmoke.com/book.htmOur coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmokeOur Book Store: http://astore.amazon.com/contracross-20
Today is Sputnik Anniversary Day! Michael, AA1TJ, and his intrepid international band of solder melters will be putting their homebrew Soviet-parts rigs on 15 meters! I will be listening with my HQ-100. This is all discussed on SolderSmoke 138, which I have just uploaded: 
That's a homebrew triode built in an apartment workshop by the intrepid Polish radio wizard Aleksander Zawada. The last line in the blog post really got to me: "All is needed now is to solder a socket to the base of the triode, and use it to make (for example) a regenerative radio receiver!"
Check it out: http://lekernel.net/blog/2011/09/prywatna-wytwornia-lamp-where-diy-meets-vacuum-electron-devices/
Mike, KC7IT, alerted me to this one. Check out the decoration on the top of this box. The artist explains: 
The temperature has dropped to around 10 C today. Fall is in the air. So it was appropriate for me to do some work on an old tube radio. (Several of our correspondents have reported similar seasonal urges to melt solder and to heat filaments.) This week my trusty Drake 2-B was giving me trouble on 17 meters. It was working on all other bands, but not on 17. Today I put it on the bench, pulled out the schematic and started troubleshooting. I quickly determined that the problem was, in fact, with the 22 MHz crystal. The 2-B has a 24.5 MHz rock for tuning the lower portion of the ten meter band. When I put that crystal in the "E" socket (where the 22 MHz crystal normally sits), the local oscillator worked just fine. Putting the 22 MHz rock back in the E socket resulted in no oscillation. And when I tried to the 22 MHz crystal in the 10 Meter socket normally used by the 24.5 MHz rock... nothing. What causes a perfectly good crystal to go bad like this? 
Oh man, this is some fascinating stuff: old light bulbs found to be oscillating at VHF! Wayne, VA7AT, stumbled upon this phenomenon at age 13 while engaged in Knack activities. Now Joe Sousa explains the physics behind the emissions that caused Wayne's light bulb to interfere with the broadcast of baseball games. How long until AA1TJ has one of these bulbs on the air, making contacts? There is much in this that would appeal to Michael: light bulbs, weird physics, translations from German... You gotta love the BNC connector plugged directly into the bulb. Check it out the radio museum article here. 
The Chief Designer, Michael, AA1TJ, alerted us to this wonderful post on Roger, G3XBM's blog: 
Posts
All Comments
Posts
All Comments
