My Eleven Contacts using the SolderSmoke Direct Conversion Receiver -- It is NOT a toy!

I have made 11 contacts using the SolderSmoke Direct Conversion receiver.  Ten of the 11 were after June 3, 2025. This was in very casual operation, operating with less than 1 watt with a dipole antenna.

Alan W4AMV

1. The first of course was back in February 2023 with W4AMV.   On this one I was using a simple "10 Minute Transmitter" that I threw together thinking that I would use it to demonstrate the receiver to our high school students.  "Wait a minute," I thought.  I called CQ and W4AMV answered.  I was running about 100 mW. He too was using homebrew gear.  https://soldersmoke.blogspot.com/2023/02/first-qso-with-high-school-receiver-100.html

2, 3, 4.  On June 4, 2025 I again fired up the 10 minute transmitter.  My T/R scheme was VERY simple: I have an MFJ coax switch that I use to select the rigs that will connect to my various antennas.  On the antenna switch I selected my 40 meter dipole.  I ran two pieces of coax from two different positions on the MFJ switch.  One I marked RX, the other TX.  The transmitter and the receiver were working off 9 volt batteries. I quickly worked N2WJW. Gil in New Jersey.  But I noticed that the 10 Minute rig was drifting.  So I pulled out my trusty old Tuna Tin 2 transmitter and used it to heartlessly replace the 10 Minute Transmitter.  Now with SEVERAL HUNDRED milliwatts, I worked W2XS, John in New York on June 5, 2025.  Later that same day I worked N9FGC in Indiana.

 

K1OA's Rig

5. My most amazing contact came on June 7, 2025. Here is my log entry: 40CW K1OA First 2 way contact with station also using a SolderSmoke DC Receiver!At around 0630 EDT on June 7, 2025 I heard K1OA calling CQ on 7030 kHz CW. This was exactly where I had a crystal.  I called him, but he didn't hear me.  I sent him an e-mail.  We tried again -- he heard me calling him and I heard him responding by calling me, but I don't think we succeeded in exchanging signal reports. It was close, but no cigar.  I had to walk the dog. Scott and I agreed to meet on 7030 kHz at 0730 EDT.  Arggh.  There was a QSO there.  I thought we might have to try to change frequency, but this would have been tough because both of us were crystal controlled on transmit.   Fortunately, the contact on 7030 kHz wrapped up.   Scott called me, I responded, and we were able to exchange signal reports.  I was so excited that I almost forgot to hit the record button on my phone.   But I caught the last minute or so.This was really something.  This really goes to prove what Dean and I have been saying all along:  this receiver is not a toy!  It can be used for real ham radio contacts.  And now we have had these receivers on both ends of a contact.  For transmit, Scott was using a KA4KXX transmitter with about 3 watts output.  I was on my Tuna Tin 2 at about half a watt output.

Jim W1PID

6, 7, 8.  Later on June 7, 2025 I worked an old friend, Jim W1PID.  Jim is a friend of Homebrew Hero Mike AA1TJ, and was involved in Mike's effort to cross the Atlantic with a voice-powered rig.  Jim also was one of my contacts with the ET-2 QRPppp rig. I also worked WZ2J  Vin in NJ. I also worked John W2XS again. 

Mike WB8VGE

9.   June 11, 2025  (Really evening of 10 June 2025) Famous homebrewer, Anchorologist, Heatkit authority and fellow member of the QRP Hall of Fame Mike Bryce called me!  40CW 0034 WB8VGE Mike Bryce came back to my CQ! Mike wrote: Nothing like quartz locked frequency control!You know it sounded pretty damn good at 500mW. You were holding your own until QSB would take you out in a deep fade. But all in all, one hell of great QRP QSO.I was running my Ten Tec Scout that I had just put back together a couple of days ago.  Got around to putting the case back on it tonight, and had it cooking in the back ground just listening to the stations come and go. I had worked a few POTA stations near by and found a quite spot. I was working on a project when I heard your CQ through the din of the 40M band. Glad I took a break and worked your QRPp signalbest 73  QRP # 4816 You get a QSL for that QSO!

Here's my post about Mike, WB8VGE:  https://soldersmoke.blogspot.com/2018/09/wb8vge-on-qso-today-qrp-hb-boatanchors.html

10. Around June 11, 2025 I worked W4MY in a contest. 

11.   On June 12, 2925 I worked some DX with the rig.  It was VA3ICC, Ian in Ontario. 

Ian VA3ICC

All of this reinforces something that Dean KK4DAS and I have been saying all through this build process:  this little DC receiver is not a toy.  It can be used as a serious ham radio receiver and it can -- even when paired up with a very low-power crystal-controlled transmitter and a simple antenna -- make some great ham radio contacts. 

Mike WU2D POTA CCC Camp Activation (21 October 2024) with 1930s-era Station -- See If You Can Contact Mike!

Frank Jones lives!  See if you can work Mike on Monday.  Let us know if you do! 

--------------------------------

Bill,

 

I’m scheduled to tour the Civilian Conservation Corps. Camp at Bear Brook State Park here in NH on Monday. This is the largest totally intact camp in the country.

I will be activating POTA with the 1930s portable Station. The POTA CCC Camp event is scheduled for Monday around 2:30 ET (if I get everything setup after the camp tour). Primary 7057 kHz Sec 7054 kHz.

 

The station is an internal battery powered, push-pull Jones Oscillator Transmitter at around 3 Watts out, and a two-tube regenerative receiver that is a period ham artifact. So, four type 30 battery tubes in total.

The antenna is a single wire feed Windom with suspended counterpoise so basically an Off Center Fed Hertz (OCFH).

 

Between the weather, running the station, logging, and doing camera work, and of course, MURPHY - this should be nuts.

1930s Regen with Transmitter – Fully Self-Contained Portable. Note Charger that is attached to top off the internal battery on transmitter. I did not buy the proscribed 25 9V Batteries and make a TX HV pack up! I used a DC-DC converter and a LiPO drone battery! The Receiver is 100% Dry Cells However.

 

73’s Mike WU2D

----------------------------

More info here: https://www.youtube.com/watch?v=N2Pdprx0ItY

And many other great videos on Mike's YouTube channel: https://www.youtube.com/@MIKROWAVE1

Ragnar LA1UH's Wonderful Museums in Norway

Here are two more great museum visits by Helge LA6NCA.  In these two he visits Ragnar LA1UH.  

Ragnar has a lot of maritime experience, so we see a lot of older ships' radios.  But his interest in the radio art is much broader and we also see a lot of other kinds of gear: 

-- Wow,  a "travel radio" in a suitcase from 1927.  Was this the idea that later lead to the Parasets of WWII? 

-- Lots of "Stay Behind" gear from the Cold War. That "Africa" receiver (that never made it to Africa!) is very interesting. 

-- We see an ART-13 with autotune, ANGRC-9s, several ARC-5 command sets.  I was hoping Raganar would fire up a Dynamotor, but no. 

-- I spotted a Galaxy V transceiver.  I have the VFO reduction drive from one of these in my homebrew 15/10 rig.   

-- We see several variometers in the emergency (500kc?) maritime transmitter.  I used a variometer in my super-simple ET-2 transceiver (with an N0WVA receiver). 

-- Lots and lots of tubes. 

Ragnar says he himself is of 1944 vintage. I hope some "stay behind" provisions have been made for these amazing museums. 

Thanks to Helge LA6NCA and to Ragnar LA1UH.  

SolderSmoke Podcast #250 Dean KK4DAS joins Pete N6QW and Bill N2CQR

SolderSmoke Podcast # 250 is ready for download: 

http://soldersmoke.com/soldersmoke250.mp3

VIDEO VERSION: (1707) SolderSmoke Podcast #250 -- With Pete N6QW, Dean KK4DAS, and Bill N2CQR - YouTube

Intro:   Welcome to Dean KK4DAS.  For 2024 Pete and I hope to jazz things up a bit by bringing in fellow homebrewers to talk about their projects.  Dean is our first victim.  Welcome Dean. 

Some good news:  Several new homebrew receivers are inhaling:  Armand WA1UQO in Richmond has an amazing looking regen.  Scott KQ4AOP in Tennessee got his DC RX working.  Mike AG5VG in Texas has been homebrewing BITX 20s and BITX 40s.  All are on the blog.  

Pete's report: 

-- Recent blog entries on filters,  SSB rig architecture, and of course digital VFOs. 

-- Phasing measurements, quadrature, and the Seeed Xiao RP2040

-- Error in QST article on early SSB transceiver.  ANOTHER ERROR!

--LC VFO on blog!  FB Pete!  

Dean's report:  

-- Tales of woe on the homebrew sBITX

-- Help from Farhan.  

-- Ground Bounce.  FFT Hallucinations.   Wisdom files.

SHAMELESS COMMERCE DIVISION:   

-- Whenever you are tempted to buy something from AMAZON, just start at the Amazon symbol on the right side of the page.  We get a cut from Bezos, and it doesn't cost you anything.  

-- You can try to do the same thing with E-bay.  We are finding a lot of great parts there. 

-- If you see a SolderSmoke post on Facebook,  please Like and forward. 

-- Become a patron!  Go to the Patreon page.  We put the money to good SolderSmoke use. 

-- Visit Mostly DIY RF and buy a PSSST kit!  

Bill's bench:  

-- Building yet another BITX dual bander.  15-10 again. Tried to use a 25 MHz filter left over from the earlier project, but I had to build another.  Built a new VFO using the variable cap and anti-backlash gear recommended by Pete.  Was a bit tough to get the receiver sounding good.   Had a diode ring as the second mixer, but went back to a singly balanced mixer. 

-- 10 meter AM -- Thanks to Jerry Coffman K5JC for mod. 

Other topics: 

--Counterfeit chips.  Why? 

MAILBAG: 

Wes W7ZOI 

Jim Cook W8NSA  Transoceanic BFO

Grayson KJ7UM -- Vintage Computer Museum

Chuck Adams --Glad to hear that Chuck is doing well.  

Frank Harris  K0IYE --  NO CHIPS!!!! 

ED DD5LP  Antenna software

Eldon KC5U  10 AM We  made a contact

Joh DL6ID  10 AM   

Phil   W1PJE of MIT   10AM   Where is L5? 

Bob WP4BQV now in UK 

Dino Papas KL0S in Wilmington   Reverse Polarity protection. 

AA7EE Dave Richards  Liked Armand's receiver

Rogier PA1ZZ  

Jonathan-san W0XO  Listened to my ET-2 CW Whoop,whoop

Nick M0NTV  Great videos from Nick the Vic

Will KI4POV  Working on his own SSB rigs.  

John West -- Who is the South American ham who made his capacitors and heat sinks? 

Ed KC8SBV  Working on DC receiver, experimenting with FETs 

Mike WN2A great contributions.  Si5351 sole source danger! 

Nick N3FJZ -- watch out for dead bands when testing receivers! 

Don KM4UDX encouragement from new Prez of VWS

Dave K8WPE Likes QF1 Cap backlash.  Says I'm getting soft! 

Dave WA1LBP My fellow Hambassador, from Okinawa USMC Sergeant with a workshop. 

The Art of Electronics #5 Paul Horowitz on SETI (and lots of other radio stuff)

In 2016 Paul Horowitz  talked about SETI at Google. Fascinating stuff.  Paul did an especially good job of weaving in a lot of radio/electronic and computer info.  

-- I was pleased to learn that one of the early radio astronomy antennas used plywood covered with copper.  I hope it was copper tape! 

-- I didn't know that the Fast Fourier Transform was something developed in the 1960s. 

-- Parkes Telescope!  Yea! 

-- Paul's "chirping" of receivers to screen out targets that are NOT doppler shifting (i.e. terrestrial signals). 

-- Paul tells the group that "amateur" does not mean unprofessional -- it means that the person is doing it for the love of doing it.  Amen. 

-- SETI at Home. 

-- Tube op-amps!  (was that two 12AX7s?)  

--  A variometer!  Wow!  I have two here -- one in the ET-2 regen receiver  (a gift from Pericles HI8P), and another that I homebrewed using a 35mm film can.  

Great stuff from Paul. 

SolderSmoke Podcast #248 -- Back from the Summer -- Spurs and Filters, S-meters, 6BA6 mania, Shirtpocket rigs, MAILBAG

The PsssT Kit, coming soon from Mostly DIY RF

SolderSmoke Podcast #248 is available for download: 

Audio: http://soldersmoke.com/soldersmoke248.mp3

Video: (800) SolderSmoke Podcast #238 -- Spurs and Filters, S-meters, 6BA6 mania, Shirt-pocket rigs, Mailbag - YouTube

Travelogue:  Trip to the Dominican Republic 3-9 August.  Thinking about the M0NTV video on mixers...  

Solder Smoke Shack South is almost done.   I am thinking about workbenches, operating tables and antennas.  How high should an electronics workbench be?   Table height?  Or workbench (woodwork) height?  

My son and I went to see "Oppenheimer"  Trinity test scene very cool.  They wanted to see if the gadget would work! 

Is the SolderSmoke blog completely archived on the WayBack Machine?  Please check and let me know.  Thanks. 

Bill's Bench: 

-- I've been working a lot of DX with the homebrew rigs:  Indonesia, Australia, Japan, Hawaii.  Lots of fun.  15 meters has been especially good. But the rigs still need work: 

-- M0NTV's video got me to put TinySA to work.  I found that output from dual banders could be improved.  Spurs and harmonics. Yuck.  I need more TinySA -- ordered the TinySA Ultra. 

-- Allison KB1GMX helped a lot.  EB63A amp was unstable, especially on 10 meters.  Higher frequencies are harder!  Tightened up shielding, negative feedback, and bypassing.  This all helped, but I found that I needed to take the higher frequency LP filters out of the amplifier box.  W3NQN filters are better, with steeper skirts and better 2nd harmonic rejections. NanoVNA proving very useful. https://www.gqrp.com/Datasheet_W3NQN.pdf

-- Also worked on the Bandpass filters for these rigs.  Farhan's comments on skirts of different filter configurations.  Some are "LSB" filters (with steeper skirt at the highest freq) and some are "USB" filters (with the steeper skirt at the lower frequency)  See diagrams on the blog page. So I built USB new filters for 12 meters and for 10 meters. 

-- Danger that my unshielded wooden box rigs might be inviting feedback.  So I shielded the 1510 rig with copper guitar amp tape (conductive adhesive).  Good stuff.  

-- Phase Noise rears its ugly head again.  See blog posts. 

----------------------

SHAMELESS COMMERCE DIVISION:  

Mostly DIY RF getting ready to release PsssT kits.  Target date:  December 18, 2023 (E Howard Armstrong's birthday).  https://mostlydiyrf.com/

Amazon Search box seems to have died.  I can't get it back.  Can anyone tell me what happened?  (There seems to be "explanations" from Amazon about this, but they are written in a strange language that I cannot follow.)  Something similar happened with the Google Ads on this blog page.  Apparently you can't have ads both on YouTube and blogger.  

But hey, there is Patreon for those who want to support the podcast and blog. 

-------------------------

Pete's Bench

An S-meter for Bill? 

6BA6 Mania! 

QRP SSB with 6BA6

Shirtpocket rig re-build

Mailbag: 

Walter KA4KXX has a great article about homebrewing in the September 2023 QCWA Journal.  

 Steve KC1QAY -- Has joined the CBLA.  I sent him a 3579 crystal.  He built a MMM and experienced JOO.  And Allison KB1GMX is in his local radio club.  TRGHS. 

Ajay VU2TGG in Pune, India -- launching a high school receiver effort. 

Denny VU2DGR The Wizard of Kerala: https://soldersmoke.blogspot.com/2023/08/the-wizard-of-kerala-india-denny-vu2dgr.html

Joe VK4BYER working with kids a remote Australian community.  FB. 

Todd K7ZF -- Wants to get into homebrewing. Advised him to start small. 

Dean KK4DAS:  Fixing Hallicrafters Worldwide RX. Ciudad Trujillo!  Got question from Mark in the VWS Makers Group:  HOW DOES Michigan Mighty Mite REALLY Work.  See blog. 

Trevor Woods -- Info on Super Islander Mark IV made in Cuba from old CFL bulbs.  FB. 

Bob KD4EBM sent me some great stuff:  Sony SW receiver,  QCX Mini.  Made a CW contact with the QCX.  Felt virtuous -- it is going to the DR.  Thanks Bob. 

Peter KD2OMV:    One of the guys I worked with the ET-2 transceiver.  Great to hear from him. 

Armand WA1UQO   Richmond area radio museum? https://www.youtube.com/watch?v=BSCmljje1p8

Mike WN2A -- Sent me a great care package with lots of toroids.  A lifetime supply!  Thanks Mike!

Nate KA1MUQ got his Doug DeMaw receiver going after 38 years!  FB.  Been there, done that! 

Tony: G4WIF Liked Valveman video about Gerald Wells.  He visited him! https://soldersmoke.blogspot.com/2023/08/valveman-story-of-gerald-wells.html 

Dean KL7MA  Bill talked to him on 15 SSB.  He had worked Wes W7ZOI!  FB! 

The Awesome Homebrew of Will KI4POV

 

Will's homebrew station is really something.  The rig (it truly qualifies for this term of praise) is amazing all by itself  (see below), but a look at Will's QRZ page reveals other ingenious inventions and techniques:  There is the clock made from panel meters.  And the method he uses for making aluminum project boxes.  He even made an N0WVA regen receiver.  That's the one I used in my ET-2.   Fantastic.  

Will really needs to share his homebrew skills with others.   I hope he is soon in a local high school teaching students how to build things.  Thanks Will!  

Bill and Pete,

Just wanted to send a note to update you on the latest projects here. The last time I emailed, I mentioned wanting to build a superhet, which you (rightfully) discouraged, pushing for a DC receiver.

Well, I finished the superhet at the end of last year. I had most of the receiver working long before then, but got bogged down in an AGC system. The final receiver is a 5 band si5351a controlled single conversion superhet loosely based on Todd, VE7BPO's design with several modifications. I used a 9 Mhz IF instead of 4, I used a digitally controlled LO and BFO, and as mentioned, I added an AGC system, which ended up being the most challenging (and most interesting) part. The final AGC system I ended up with used the detector and amplifier side of Wes Hayward's "full hang" AGC from SSDRA, but I didn't have the IC IF amplifiers with variable gain, so instead, it fed a PIN diode attenuator circuit to control the IF gain. The final result worked great, but I nearly pulled my hair out getting it to work. I originally intended to build the receiver for 40 and 20 meters, but it ended up covering 80, 40, 30, 20, and 15 since I used the filter relay board from QRP Labs which had 5 slots.

After I got the receiver running, I decided I needed a matching transmitter, so I  built up a simple CW transmitter to match. It uses an si5351a VFO driving a 74HC04 hex inverter as the buffer amplifier. The trick here is that by driving all the inverter gates in parallel, the output impedance is ~14 ohms broadband, suitable for driving a BJT PA without any need for matching transformers. The PA is 3 2N2222s in parallel with heat syncs putting out about 2 watts from 80 - 15.

The part I'm most proud of is that I have the arduino for the receiver connected to the arduino for the transmitter through a serial line. The receiver sends it's current frequency to the transmitter so that the transmitter can track the receiver's frequency as you tune (like a transceiver). I'll attach a few pictures of my homebrew station below. The transmitter is on the left, receiver is on the right. The box on top of the transmitter is my homebrew keyer. Next up on my build list is a solid state T/R switch.

Bill, I've enjoyed following the updates on the school DC receiver build. My local club is wanting to do some youth outreach, and I'd love to get them involved in building. I'm the only builder in the club though, so I don't know if I personally have the manpower to make it happen. Also, thanks for the recent info and pictures of Cuban homebrew rigs. I grew up listening to Arnie Corro, so I love seeing their resourcefulness and ingenuity. Makes me want to take apart some old electronics.

Pete, I'm enjoying following the 10M SSB project. With the uptick in propagation, I've been bitten by the 10M bug, and I'm thinking a 10M rig may have to be on my project list for this year.

73,

Will - KI4POV

KI4POV's Clock

KI4POV's N0WVA Regen

SolderSmoke's 2006 Interview with Farhan (and pictures from his 2019 visit)

Farhan in N2CQR shack with ET-2 on bench

October 2019

Here is the YouTube version of the SolderSmoke Podcast #34

 https://youtu.be/q-L4IE9f1aA

Farhan with Bob Bruninga WB4APR (SK) 

https://www.qrz.com/db/WB4APR

With Bill and Abe Lincoln

With Einstein

Correcting an Einstein equation

With Elisa

Tuning Bill's BITX 20

SolderSmoke FDIM Interview: Adam K6ARK and his 2.6 gram Mini-Pixie SMD Transceiver

I've not bee a big fan of the super-simple Pixie transceiver, but Adam K6ARK could make me a believer. 

Our correspondent Bob Crane W8SX interviewed Adam at FDIM.  You can listen to the interview here: http://soldersmoke.com/2022 K6ARK.mp3

The video above shows Adam's tiny Pixie in action in the California desert.  His rig is about the size of a postage stamp and weighs about 2.6 grams. FB Adam. 

Adam did a lot better with his Pixie than I did with my far larger and more complicated SST transceiver. He also did better than I did on 40 when I was using my ET-2 (two FET) transceiver. 

I liked how Adam recorded in the field the CW from his rig, I also liked his key (!) and his EFHW antenna and "tuner."  Adam's ability to cope with no CW sidetone was also admirable.  

Adam's YouTube channel is here: https://www.youtube.com/c/K6ARKPortableRadio

Thanks to Adam and to Bob Crane.  

SolderSpace! N2CQR from Geostationary Orbit

 

Farhan VU2ESE kindly invited us to talk to his Lamakaan Amateur Radio Club.  They did a simulcast through the QO-100 Geostationary Satellite.  This picture shows N2CQR being beamed into India from 22,500 miles.   Note the ET-2 and the Mythbuster on the bench.  This was a lot of fun.  Thanks Farhan! 

The Lamakaan Annual Radio Convention Starts Today!

 

The Lamakaan Amateur Radio Club's annual convention begins today in Hyderabad, India.  This is Farhan's club so it is sure to be a great event.  Presentations are being live streamed on YouTube and on the QO100 geostationary satellite. 

Here is the link to the convention: http://www.larc.in/larc4/

Pete N6QW will be the first presenter and will talk about his new PSSST Rig. He will be speaking at 0430 UTC Saturday 11 December.  That is 11:30 pm on Friday, December 10 on the East Coast of North America.  

I will be speaking at 1130 UTC on Sunday December 12.  That is 0630 Saturday 11 December EST. I'll be talking about the Mythbuster rig and about the ET-2. 

Here is the schedule.  

Here's a time zone converter: https://www.timeanddate.com/worldclock/converter.html?iso=20211211T043000&p1=505&p2=250&p3=137

Here is the Lamakaan Club's YouTube Live Channel.  https://www.youtube.com/watch?v=cRznKwGgvDo

I don't know how we might be able to watch or listen via the QO100 satellite.  The U.S. is not in the footprint of this bird.  But there is a good WEBSDR receiver run by BATC and AMSAT DL: https://eshail.batc.org.uk/

SolderSmoke Podcast #233: PIMP, Boatanchors, Novices, MMM, Heathkits, DC Receivers, Mailbag

SolderSmoke Podcast #233 is available. 

http://soldersmoke.com/soldersmoke233.mp3

Travelogue: Cape Cod. SST. Marconi Site.

The WFSRA:   The World Friendship Society of Radio Amateurs.

Pete's Bench:

The Pimp.
The NCX rig.
The Collins.
The many DC receivers built worldwide.
The parts shortages are real! Several key radios on hold. Si5351 sub.
Talk to G-QRP convention

Bill's Bench:

FT-8. Not for me. I tried it.
Novice Station Rebuild.
Globe V-10 VFO Deluxe.
Selenium rectifier removal CONTROVERSY?
Not crazy about my Novice station. Not crazy about CW. 
Mate for the Mighty Midget. Again. 
Mike W6MAB -- Detector problems LTSPICE Check
One more mod for MMM RX. Ceramic filter at 455.
Dropped screw inside tubular cap on Millen 61455 transformer. 
Talk to the Vienna Wireless Society
Thinking of a Moxon or a Hex beam.


BOOK REVIEW Chuck Penson WA7ZZE New Heathkit Book. http://wa7zze.com

Mailbag

-- New SPRAT is out! Hooray!
-- Todd K7TFC sent me copy of Shopcraft as Soulcraft. FB.
-- Dean KK4DAS building an EI9GQ 16 W amp. FB.
-- Jack NG2E Getting close on Pete's DC receiver.
-- JF1OZL's website is BACK!
-- Tony K3DY sent link to cool books. 
-- Sheldon VK2XZS thinking of building a phasing receiver.
-- Peter VK2EMU has joined the WFSRA. FB!
-- Ned KH7JJ from Honolulu spotted the Sideband Myth in the AWA video.
-- Chris M0LGX looking at the ET-2, asks about the variometer.
-- Pete Eaton Nov 64 anti HB rant in november 1964 QST. Wow.
-- Josh Lambert Hurley spreading FMLA stickers in the UK. FB
-- Stephen VE6STA getting ready to melt solder.
-- Got a great picture of Rogier PA1ZZ back on Bonaire.
-- Farhan reading the manual of Hans's new digital rig.
-- Paul G0OER wonders if FMLA getting ready to move on 5 meters.

VE7SL's Beautiful Single Tube Transmitter and Single Tube Regen Receiver

Just stunning, in their simplicity and beauty.  Really amazing work.  Kind of reminiscent of my ET-2, but with tubes, and much nicer construction.  More details here: 

RECEIVER: https://qsl.net/ve7sl/neophyte.html

TRANSMITTER: https://qsl.net/ve7sl/neotx.html?fbclid=IwAR3cM6tSRjyTsNouHWVz_buuzz4C9O-IwQbdZM5dekkle69ZW7-JBQcHTVI

Three cheers for Steve VE7SL!  I've been linking to his blog for several years, but somehow I missed this magnificent red rig.   

Steve's online notebook: https://www.qsl.net/ve7sl/

Steve's blog: http://ve7sl.blogspot.com/

Ciprian's Romanian Ten Minute Transmitter with Roots in SPRAT, KA4KXX, and the Florida Sunrise Net

It sounds great Ciprian!  It was really cool to see your video and hear you reference not only the SolderSmoke blog, but also SPRAT, the Michigan Mighty Mite, and Walter KA4KXX. Your little rig has a very fine lineage!  

I found Ciprian's video just after seeing the wonderful Herndon Mighty Mite of Jack NG2E.  TRGHS!  The Color Burst Liberation Army is on the march!   For more info on NG2E's Mighty Mite, check out his blog: https://jackhaefner.blogspot.com/2021/05/mounting-to-perfboard-and-scope-test.html 

Jack has in his possession one of the  7.123 MHz crystals that Walter KA4KXX sent me back in 2019 (during my ET-2 craze).   It seems obvious that Jack should build a Ten Minute Transmitter and use it to check into the Sunrise Net  https://qsl.net/srn/. 

ON6UU's DB4020 EA3GCY Rig

Hi,

Recently I got the EA3GCY newsletter,  it announced a new kit DB4020,  a 2 band transceiver kit covering 40 and 20 mtrs.  I know Javier EA3GCY’s kit are good so I ordered one.  A week later it arrived in a brown enveloppe in which I found all components and printboard wrapped in bubblewrap,  it was all well packed and after checking all components all was accounted for,  all components were indeed there.

8 toroids have to be wound,  following the instructions it was piece of cake,  no problem,  

After several hours of work - relax max style - I got everything in place to test,  hurray,  no smoke !!!!  So now the SSB part was ready,  I have 7W on 40 and 3.5W on 20mtr.  Good power for qrp sota,  wff or just garden activity.  A fortnight later I got notice that the CW part of the kit was ready and another week later it arrived here,  I soldered the 2 boards as soon as possible to get a multimode 2 band transceiver.   The 2 boards are the CW interface which also holds the KB-2 keyer,  the second board is the 500-600HZ CW filter.   The KB-2 give the user 4 memories,  beacon function and some more functions.  Good thinking to include the keyer,  it makes life easy when you’re on an activation. 😊   I opted to make the filter switchable,  I like to be able to listen broadband too,  very simple,  cut one leg of the 13 pin connector on the bottom of the CW interface and put a switch on both ends.

After some figgling around I also got the box ready,  a military grade plastic box with wall thickness of 5 mm,  this box should be able to withstand a lot of shocks and a drop to the ground.  I also made a docking station for a laptop battery which holds some 5Ah and which should be able to give me a lot of hours of listening and some 2 to 3 hours of operation.  I had an old laptop which the screen was broken and had some other malfunctions,  I have taken the battery connector out of it,  luckily I still have another laptop which still works and this is the charging station for the batteries …. ..  😊   The docking is only to test,  I will box it up in maybe a some box where I can then maybe also fit a end fed solution or tuner for coax fed antennas.

A new radio also needs a new CW key so I made one out of an old relay,  painted the base green to fit somewhat the box et voila,  here is the result of the complete portable station.

The key can be fitted to the box by means of a bolt and a wingnut.  A short cable goes to the CW connector of the transceiver.

I had a lot of fun constructing this kit,  the box,  the docking and the key.   For 180€ you get a arduino nano controlled CW/SSB transceiver with 2 bands on which most of the activity is and you also get a keyer with memories.   Good deal I think.   More info is available on EA3GCY’s website.  Javier is also very quick in responding to questions,  he ask for opinions and offers almost an Elecraft style of service.

I made some video’s which are on youtube :

https://www.youtube.com/watch?v=Y9sUbyAlF00&t=12s

https://www.youtube.com/watch?v=hGDwLdkr3HU

https://www.youtube.com/watch?v=ZiMnpfte4cI&t=35s

https://www.youtube.com/watch?v=oLYIgVv7So8&t=130s

The kitters website :

https://www.qrphamradiokits.com/

https://www.qrphamradiokits.com/transceivers/db4020-dual-band/#cc-m-product-12710260049

Best 73

Frank

ON6UU

SolderSmoke Podcast #216 Is Available: BITXs, Paesano, Paraset, ET2, Antuino, Mailbag

Bill's uBITX with HB keys and the mic that used to be the podcast mic! 

SolderSmoke Podcast #216 is available 

21 December 2019

HAPPY HOLIDAYS TO ALL! 

http://soldersmoke.com/soldersmoke216.mp3

Pete's Bench 

Sprat Article

BITX 40 Fun

ZL2BMI Rig

Paraset.   Three tubes!  Almost an ET-3!

Bill's Bench

ET-2 Adventure over,  Rig on the wall

Final QSO count. 20   3 "random" 

Last QSO with AA8OZ

Lessons learned:  100 mW not the problem. Crystal Control cramps your style. 

N0WVA regen amazingly effective.

Tried for the Sunrise Net.  Walter sent me some crystals.  

On to the uBITX. 

Accidentally wiped out calibration and BFO settings. 

Had to do recalibration and reset BFO. 

Learned a lot about the rig. 

How they did CW and how they do it now. Shift TX?  Or shift RX?  Or just shift BFO on RX? 

How all the signals end up as upper sideband.  Only one BFO freq.  Very cool. 

TalentCell 12 V Lithium Ion 3 AmpHour battery. Size of a deck of cards. 

Inspired by Peregrino -- I ordered EFHW Tuner from QRP Guys. 

Homebrew Straight Keys

Antuino upgrade 

SMT soldering. 

Back to Arduino Nano and the IDE.  

A very cool tool. 

Antuino filter analysis.

Version 6 of uBITX out. 

The "Watt Meter" DC power meter.  Very useful.  8 bucks.  LINK:

https://www.ebay.com/itm/Digital-DC-combo-Meter-LCD-Watt-Power-Volt-Amp-RC-Battery-charging-Analyzer-M/152339793114?fbclid=IwAR0u9SlZi2Dm6zOJyZt4fDTu7w_pjBIEYD_FiNfLymxtQUbMjcNHjfB17P0

SPRAT, balloons and hardcore homebrew hydrogen. 

MAILBAG

VK3HN's AM receiver.  I ordered 6kHz 455 kHz filters from Australia. 

Dean's MMM

Peter VK2EMU   Hertz not hertz. 

Ben KC9DLM LTSpice YouTube Videos

Steve Silverman  Electroluminescent Receiver Kit

Lyndon N0LFX back to listening.  FB OM

Steve M0KOV built a pill bottle variometer.  Did you get the regen going? 

Anthony VU3JVX   FB HB uBitx.  

Allison KB1GMX  Great to hear from her

Leif WB9IWT -- helped me trouble shoot my uBITX (BFO was low)

Mike EI0CL  old buddy from Azores days.  Recognized his voice on 20.  Great QSO.  

Hangin' it up (the ET-2)

My ET-2 minimalist QRP CW adventure is (for now) officially over.   I have taken the rig - festooned with the callsigns of all the stations I contacted -- and have put it up on the wall.  This may be a new form of art.  I think I am the first radio amateur to do this.  I think it is pretty cool. 

Here are the stats:   I made 20 contacts with the rig. I had it on the air from 12 October 2019 to 7 December 2019.    Seventeen of the contacts were the result of my posting pleas for help on the SKCC Sked page and/or the Summit DX page.  Three of the contacts were completely random. One station -- W1PID -- provided four of the contacts.  Thanks Jim. 

My power out was usually around 100 milliwatts.  I used either a 40 meter coax fed dipole or a 135 foot doublet fed with window line. 

My best distances were Wisconsin and Georgia. 

Crystal control was the real limiting factor.  100 milliwatts didn't seem to be much of an impediment. The most amazing thing about this rig is the N0WVA regen receiver.  It took a lot of peaking and tweaking, and it took some skill to operate. but once I got it going it was an amazingly good receiver.  Really Amazing for just ONE J-310 FET. 

The last contact was really nice.  I was calling CQ and AA8OZ came back.  He was in a cabin on a trip with some scouts.  He too was on a wire antenna.  He was one of those guys who said WOW! when I told him about the rig.  We had a nice long conversation on 40.  It was a great way to wrap up the ET-2 adventure. 

Thanks to all who helped me make contacts and for all those who tried to work me. Thanks to N0WVA for the regen inspiration. And thanks to Glen Yingling W2UW (SK) for the ET-1 idea. 

The rig is standing by.  On the wall.  Perhaps it will return to service, maybe during solar max. 

Crystals -- Old and New and World War Two

I was watching Greg Charvat's great video about the WWII ARC-5 receiver yesterday. Greg admonished all of us to preserve any WWII gear we might have in our shacks.  Just one day earlier I had found the crystal pictured above in my junk box.   There is some old stuff floating around in here! I will preserve this one. 

Speaking of crystals,  Walter KA4KXX recently sent me some 40 meter crystals for use with my ET-2 transceiver.  Walter suggested that I use them to check into the daily (1300Z) Sunrise Net on 7123 kHz.  These were modern "short" computer crystals.  So I put them into FT-243 and FT-241 holders.  (Don't worry Greg, no WWII gear was destroyed in the process).  It was kind of fun to put the new rocks in old boxes. They work just fine in the ET-2.  Thanks again Walter! 

Finally, Chris KD4PBJ has been helping a buddy of his buy a Drake 2B.   This morning Chris asked about the E Crystal adjustment coil on the back of the Drake.  I told him that was to allow the use of "overtone" crystals.  But, sadly, I advised him not to worry about it too much because the days of ordering bespoke crystals (overtone or otherwise) are behind us.