PH2LB's Homebrew Hi-Per-Mite CW Filter in his uBITX

I really like the way Lex PH2LB measures and demonstrates the effectiveness of the Hi-Per-Mite CW filter designed by David Cripes NM0S.   Watch the short video above.  The blue trace is the audio input to the filter, the orange trace is the output.  Watch the output change as Lex sweeps the audio frequency range. 

He wrote: 

After studying the schematic I shifting through my spare parts stock to collected the components and build one according there design on a breadboard (I changed the center frequency from 700 to 600Hz).
I hooked up my signal generator with a amplitude of 2v max and sweeped it from 250Hz to 2KHz looking at the output on my rigol osciloscoop. On 2khz VMAX=0.04V, 885Hz=0.2V, 700Hz=1.5V, 662-585Hz=2V, 400Hz=0.2V, 500Hz=0.9V, 250Hz=0.04V. So a nice flat top between 585Hz to 662Hz.

A full description of Lex's project (with more videos) is here: 

https://www.ph2lb.nl/blog/index.php?page=ubitx-mods3#ubitx-mod14

Lex's Knack Story and the intro to his blog is here: https://www.ph2lb.nl/blog/index.php?page=history

Tribal Knowledge: More on Tapping Metal

Back in 2014, when I was putting together my EB-63A solid state amplifier, I had to learn how to tap aluminum so that I could attach my transistors to the heat sink.  I did short YouTube video on how I did this (with tales of woe!).  This video turned out to be amazingly popular -- more than 27,000 views!  Apparently there is a great thirst for this kind of knowledge out there.  Recently someone in Alaska came across my video and shared with us some more useful information on how to tap metal.  Here is some tribal knowledge from Paul KL7FLR:  

Hi Bill and Pete,

Stumbled over Bill’s YouTube video about tapping in Aluminum and I would like to add my experience doing such. I have probably tapped over a 1000 holes in various metals, cast iron, steel, aluminum, bronze and brass from 0-80 to ¾-20. Each metal poses its own problems and solutions. There was nothing in error with your video or the method you presented.

My comments:

What causes broken taps is the tap is not being perpendicular to the work. A hole not perpendicular to the work, a worn/dull tap (this applies to the drill bit too) and lack of lube.
Every hole to be drilled and tapped must be perpendicular to the metal. A hand drill electric or battery will not be perpendicular unless two other people can spot the drill operator. Not possible when you are alone in the shop.

Any serious homebrewer should have a drill press. A small bench drill is very inexpensive. Even the $69 Harbor Freight model is adequate for the average ham’s workshop.  I see these items at flea markets and on Craigslist all the time cheap. Estate sales not so cheap but sometimes on last day you might get a bargain. Adjustable from 500 to 3600 rpm will cover all the normal sizes of drills. An x-y table could be added ($$) for added accuracy if desired. (search x-y table for examples and sources)

The size of hole you drill makes a difference too. Most drill charts assume you are tapping at 75% of thread contact. This is amount of the male thread of the bolt/machine screw threads contact the female thread in the piece. This is about the max you can expect without some precision tooling that won’t be in the average home shop.  75% provides maximum strength of the fasteners.  So unless you’re working on something that requires strength like a tower support bracket or the wings of an airplane you don’t need 75% as 50% thread contact is more than adequate. So when the drill chart shows that a #43 you can instead use a #42 or a 3/32 drill. A little bit larger hole will be a lot easier to tap threads.

The type of tap will also influence the difficulty of tapping threads. The typical hardware store tap is a straight 3 or 4 flute taper tap. The chamfer of a taper tap is 9 threads making tapping much easier. This is the tap for hand tapping.  The plug tap has a chamfer of 5 threads and is best used in a tapping head or fixture. The bottom tap is for tapping threads in a blind hole, usually after started with a taper tap. That increases the pucker factor x10. The normal taper tap cuts as it is rotated in a clockwise direction or counter-clockwise for left hand threads. The cuttings will clog the tap and you must back the tap out frequently to clean the cuttings from the flutes preventing the tap from seizing and possibly breaking the tap. Breakage is easily done with the smaller taps but also will happen to a larger tap too.  There is a style of tap called a spiral point tap. It will push the cuttings up to the top of the hole and not clog the flutes as easily as the straight flute taps. I still back it out and clean it out of habit. These don’t cost any more than the hardware taps. A 4-40 is about $2.90 the last time I bought one.

Avoid “carbon steel” taps. These will break easier than “high speed tool steel” taps and they are usually a few cents cheaper too.

Lubrication is necessary. Bill’s use of 3-in-1 oil is a good lube but “Tap Magic 20016A Aluminum” fluid is better for tapping aluminum and regular “Tap Magic” for everything else. https://www.amazon.com/Tap-Magic-20016A-Aluminum-Yellow/dp/B00065VEUO

The metal you are tapping can be an exercise in patience. “Hardware” store aluminum comes in various grades from crappy to real crappy. They are of an alloy best suited for the extrusion process and are not wonderful for the tapping process. Aircraft grade aluminum is nice stuff to work with but not cheap. Comes in many grades from 1000 series to 8000 to match the application. Grade 2024 is communally found and is easy to work with while 7075 works like steel.  Since most of us won’t be buying a 21 foot stick of aluminum or a 5x8 foot sheet we must take the hardware store grade into account when tapping holes and lean towards the 50% thread engagement, plenty of lubrication and lots of patience. I frequent several aluminum boat building firms and they let me pick through their scrap piles and I’ve made frequent donations of a case of soft drinks or a can of coffee to the break room fund and have also paid the going scrap price for the scrounging privilege.

Worn taps:  These get dull with use and will break at the worst possible time and in an expensive  workpiece. Broken taps  can be removed but are time consuming and require some expertise in doing so. Best to retire them when worn. I used to keep a chart of how many holes a particular tap had been used and at 35 holes for the small taps they got retired. 50 holes for taps larger than ¼”.  I once spent over a week of evenings extracting a worn tap from a locomotive cylinder casting. Never again! As my mentor said many times, “dull tools cause accidents and ruined work”.

Clamp the work to be tapped stationary if possible. You don’t want it moving around thus inviting a broken tap. Use some method of a tap guide (as Bill did with a block of wood, not great but better than nothing). I use what is called a “Piloted tap wrench”, https://www.amazon.com/Set-Wrench-Piloted-Spindle-Capacity/dp/B077SVQD4S .

Picture is of my setup.
Step 1: Work clamped securely to table at desired hole location.
Step 2: Drill hole.
Step 3: Use piloted tap wrench to tape hole.
Step 4: Done.

Hi-Per-Mite Active Audio CW Filter Installed in uBITX (video)

Coming home from the Dominican Republic, this was a major item on my list of desired mods for the uBITX: a narrower passband for CW.  Using the 2.3 kHz SSB passband, you could have many CW QSOs audible in your headphones.  Narrow that passband to 200-300 Hz and life gets a lot easier. 

Farhan had discussed adding a 12 Mhz IF filter of suitable CW bandwidth, but this seemed difficult to me. Besides, I have long wanted to use an active audio filter for this purpose. 

The Hi-Per-Mite filter from 4 State QRP Group is just what I needed. I built the kit without problems in about an hour, then I put it in the uBITX box, with  switch on the front panel that lets me put it in the circuit or take it out -- this is very satisfying and a lot of fun.  

The Hi-Per-Mite just goes between the uBITX audio out and the speaker/headphone connection. I built mine for "no gain" -- the uBITX provides plenty of audio. 

The selectivity with the Hi-Per-Mite compares favorably to that of my Drake 2-B with the 500 Hz LC filter.  You can get an idea of the performance in the video. 

Three cheers for the 4 State QRP Group and their Hi-Per-Mite!  Here is the page with all the info: 

http://www.4sqrp.com/hipermite.php

K6RRE's One Tube Rig Project

Mike will send us more info later... 

The Elektor SDR Kit: Arduinos, Si5351s, Sound Cards, WSPR, QRP Transceiver (video)

Obviously a lot of potential here.  Thanks to Hack-A-Day for the alert. 

https://hackaday.com/2020/02/14/rf-shield-turns-arduino-and-pc-into-shortwave-radio/#more-398447

The Si4730 Radio Chip (Luddite Alert!) (video)

I have misgivings about this.  Hack-A-Day presents it as a DIY radio project and wonders if this might be the modern equivalent of the crystal radio projects of days-gone-by.  But notice that the "build" video focuses mostly on building the box.  The electronic "building" of this radio mostly involves plugging in two chips, or two boards with chips. My questions are: 

1) When this project is finished, who REALLY built it? You, or the Si4730 manufacturer?  

2)  After you've "built" this thing, would you have the same sense of accomplishment that you get from an analog, discrete component project?  Or even from that crystal radio?  

Of course, to each his own.   This is all for fun.  Have fun with the Si4730.  But today I'll be working on my Hallicrafters S-38E. 

https://hackaday.com/2020/02/12/all-band-radio-uses-arduino-and-si4730/

TRGHS: Hallicrafters S-38E will NOT be Discarded (video)

My Hallicrafters S-38E was on very thin ice.  I had grown tired of the little beast.  Its dangerous no-transformer power supply had caused me to risk death and to fry one of the RF input coils (that happens if you short the antenna input to an inadvertently hot chassis). It is rickety and old and I just got tired of working on it.  I had down in the basement, awaiting disposal of some kind.  (I'd been afraid to give it away, fearing that the recipient might electrocute himself.)  But recently I've been doing some shortwave listening and this caused me to reconsider the S-38E.  

Around this time, while looking at e-bay, I saw some guy selling just the RF input coil that I had fried.  So I bought it.  Then I pulled the S38-E out of the basement and fired it up.  I realized that I had already done a lot of work on it.  I had put in an isolation transformer, so the receiver was no longer quite so dangerous.  I'd already replaced most of the capacitors.  It sounded pretty good on the AM broadcast band.  Then, in my first scan of the shortwave bands, I heard the William Tell Overture pouring from the speaker (see video).  Could it be?  Perhaps a replay of the Jean Shepherd show?  No, but I soon heard the familiar voice of Tim WA1HLR -- he was doing his show on (I think) WBCQ shortwave, just above our 40 meter band.     

THE RADIO GODS HAVE SPOKEN.  THE S-38E STAYS!  

Volcano Light in Chile

This popped up on Twitter today.  It is from 2018 -- the Villarrica volcano in Chile.   Interesting shot. The label said it was taken during a snowstorm, but I don't think that is right -- the "snow" is actually stars and that big white thing in the cone of red light is the Large Magellanic cloud.  

https://www.reuters.com/news/picture/photos-of-the-week-idUSRTS209HO

W6IQY's Homebrew SSB Transceiver from the mid-1960s

Oh wow, it is definitely a thing of beauty.  Bob W9RAN acquired this homebrew gem and put it back on the air.   Bob also wrote a very nice article about the rig and how it was made.  (Mike WU2D should brace himself -- many surplus rigs were cannibalized in the process.)  It is especially fitting that I post this today because February 9 is the day of the Classic Exchange on-the-air event.  (My DX-100 is warming up.) 

Here is the article:   http://tinyurl.com/rjqq6eo

Bob's site has some more really wonderful articles.  You can read about Heathkit monobanders, DX-60s. ELMAC power supplies and -- my favorite --  Mike Hopkins and the Five Meter Liberation Army.   The FMLA was, of course, the forerunner and inspiration for our current Color Burst Liberation Army. 

See it all here: 

https://www.rantechnology.com/index.cfm?key=browse_resources&PostDate=all&CategoryID=8E884CE4-9CED-4957-872B-5EBDB058D540 

Thanks Bob! 

AM Rally Report -- Great Contacts on 40 AM

The AM Rally this past weekend was a lot of fun.  I was reminded of how the guys that you talk to on AM are just so much more likely to be running interesting homebrew or vintage gear.

First contact was with Howard VE2AED who has one of the most amazing antenna farms I have ever seen.  Take a look:  
https://www.qrz.com/db/VE2AED
He also has an R-390 and a KWM2 in his shack. 

Next I spoke to Robert W0VMC (Voice Modulated Carrier) out in Wisconsin.  Robert is a homebrewer of AM gear with a Knack story that is very familiar:  http://w0vmc.com/

Next up was W4GON.  Joel was on the homebrew AM transmitter that we reported on back in 2017:
https://soldersmoke.blogspot.com/2017/08/thermatrons-al-fresco-w4gons-fb-hb-am.html

Joel has completed his rig, adding a FB front panel.  Here it is: 

Then came the W1AW contact.   See the video above. 

Finally, I talked to Jack W9GT who was running a rig that must be unique on the amateur bands: A Federal 167 B Maritime transmitter.  You can see this magnificent transmitter here: 

https://www.qrz.com/db/w9gt

SolderSmoke Podcast #217 -- Beach trip, '30s station, uBITX mods, HRO RX AM, ELMAC, Teensy, MAILBAG

Bill's Bavaro DR Beach Station
uBITX in the box, HB key

SolderSmoke Podcast #217 is available: 

http://soldersmoke.com/soldersmoke217.mp3

1 February 2020

Travelogue!  Dominican Republic trip.  uBITX on the Beach.  EFHW.  LiPo Battery.  First contact of the new year. 

Bill's Bench Report

Following up on proposed uBITX mods: 

-- Put pot on sidetone line from Raduino to keep the sidetone a bit quieter. 

-- Fixed the key -- pounding brass

-- Will install 4 States QRP Active AF filter. 

-- Need to reduce power on CW to 5W

-- Stereo to mono headphone adapters. 

-- Turning off display and mic amp circuit not really worth it -- they don't pull much current. 

Pete's Bench Report: 

ELMAC Power Supply project 

1930s era transmitter? 

Teensy and SDR

PETE'S IDEA ABOUT GETTING LSB AND USB FROM BITX40

KWM-2 suggestions

Back to Bill's Bench:

Working on HRO-ish Receiver. 

Bad SBL-1  

Got idea for wider ceramic filter from Paul VK3HN

Ordered parts from Mini-kits in Australia.  They sent 6kc filters. 

Bruce KK0S sent me some 10 kc filters too. 

Installed 6 kc filter with L network matching networks.  Works great. 

Also installed Infinite Impedance Detector that Paul used. 

Needed some additional amplification ahead of the IID, so I used one stage of BITX amp. 

Works great. I can tune full 40 meter band AND 49 meter SW band.  Radio Romania, China, Radio Marti, Brazil, South Carolina. 

Beefed up the shielding to cut down on AM detection. 

MISCELLANY

-- AM and DSB in LTSpice

-- Duly Noted:  Paul  VK3HN's RIG:  "THIS MACHINE KILLS KILOWATTS"  

Kanji YC3KNJ's QRPesso Expresso Coffee in the field

-- The DANGERS of powerful magnets. 

MAILBAG: 

--KK4DAS Dean doing great things.   MMM heard at Penn State.  Where is the rest of the CBLA?

-- Thanks to Don for kind donation to the SolderSmoke cause

-- Dale BA4TB -- First SolderSmoke feedback from China.  Thanks Dale!  

--Steve Silverman:  Sideswipers and bugs were made to handle "carpal tunnel of the day"  So do I need a keyer for casual CW work? 

-- Peter VK8VWA on the limited knowledge gained from kit building. Listens to podcast while walking on the beach in Australia. 

-- Allan Hale -- Clothes Pins as Toroid holders.  Yes!  More Clothes Pins   Wild Woody Keys from Dave Ingram 

-- Pete WB9FLW  100 Watt Amp from WA2EUJ  

-- Dave Wilcox K8WPE   A medical question:  Does the Michigan Mighty Mite work differently depending on what kind of medicine was in the pill bottles used for the coil form?  Good question Doc!   Dave suggest that putting CBD on the coil or the crystals.   Anything to mellow out the ham bands... 

Pete's Plank SDR
When you know stuff, you can do stuff!

WA2EUJ's NXP RF Power Amplifier Design Challenge Entry -- Won First Place Prize!

Congratulations to Jim WA2EUJ.   First Place the NXP Design Challenge. 

You can buy the board here: 

https://sites.google.com/site/rfpowertools/home/nxp-mrf-101

Thanks to Pete Eaton WB9FLW for alerting us to this.