HB2HB! AC9JQ and N2CQR Make Contact on 40 with Homebrew Rigs on Both Sides (with help from N3FJZ/HB)

This weekend brought another HB2HB (Homebrew to Homebrew) contact.   We have been following with interest the 40 meter transceiver project of Dean, AC9JQ.  Above you can watch a video of Dean's rig in action before it went into the box.  Earlier this month Dean achieved a remarkable "Double First" when he made his very first amateur radio contact.  He was using his homebrew rig to do it.  So his first contact was also his first homebrew contact.   FB. More info on Dean's rig and homebrew exploits can be seen here:
http://soldersmoke.blogspot.com/search?q=ac9jq 

This week Dean got a decent 40 meter dipole up in the air.  We arranged (via e-mail) to meet on 40 on Friday evening.  We made contact, but conditions weren't great.  We tried again several times on Saturday, looking for open spots amidst the madness of the CQ WW DX contest.  Rick N3FJZ joined us and also tried to make contact with Dean, but had no luck either.  Daytime conditions didn't allow for a good contact between Indiana and the Washington/Baltimore area where Rick and I are located. 

Finally, last night after family obligations at both ends settled down, Dean and I found a relatively open frequency on 40 and made a good contact.  A short snippet of it can be heard by clicking on the link below.   Keep in mind that Dean was running about 2 watts to a dipole on 40 at night.   

http://soldersmoke.com/HB2HBAC9JQ.mp3

Thanks Dean!  Thanks Rick!

AC9JQ's Mini Digi VFO/BFO Al Fresco with OLED (and noise test)

From Dean AC9JQ:

Just completed the VFO/BFO/Arduino/OLED module for my radio.  I also have the LPF, BPF and crystal filters completed and tested.  Next will be the audio amplifier and NE602 modules.  I will probably build one of the NE602 modules and test things out as a DC receiver.  My ultimate plan is to have the rig no more that 1"x3.5"x3".  I still have a lot of "stuff" to stuff into that size of box.  I'll keep you posted.


I have been able to contain the entire Arduino/Si5351/OLED into a small cube in the front.  The rest of the radio has to fit on two levels in the rest of the area behind the Arduino/Si5351/OLED.  I think I will build the audio section and on NE602 mixer and run it as a direct conversion first to vet out any noise or other problems.  Bill, that small coax that you pointed out will really help on this build.  I used a small piece as a power feed-thru and will use it to feed out the VFO/BFO signals, thanks again for that pointer.

I decided to test for noise on the TIA transceiver test bed.  See the video of the results.  Not too much noise.  I'm only using my indoor magnetic loop for an antenna.  Video is kind of sloppy, but taking off the antenna and turning up the volume shows how little noise is left in the system.  Now time to stuff the rest of the radio into the tight quarters.

https://youtu.be/kXf7-7FtxEU

I purchased OLED from ebay.......

http://www.ebay.com/itm/401234789687?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

0.91'' 128x32 IIC I2C Blue OLED LCD Display DIY Module DC3.3V 5V For PIC Arduino | eBay www.ebay.com IIC interface. OLED display, no need backlight, self-illumination, the display performance is better than the traditional LCD display, also lower consumption. VCC: Power (DC 3.3 ~5v). Display Color:Blue. | eBay!

They are nice and compact, although as time goes on, I'm sure they will be harder to read.  I'm hoping to have an alfresco version in a week or two.  I used much of Pete's code from the shirt pocket transceiver upgrade, modified the code to address the smaller display and add USB/LSB capabilities. 

73's  Dean AC9JQ

HB2HB! AC9JQ -- N3FJZ on 40 with Homebrew Rigs

On Saturday October 24,  Dean AC9JQ (Indiana)  and Rick N3FJZ (Maryland) made contact on 40 meter SSB using Si5351/TIA BITX rigs.  FB!:

Bill:

Dean and I made contact.  We both were in and out most of the time, but conditions seemed to improve towards the end where I could understand Dean about 90%.  Using the RST "by the book", I would say he was a 33, 3 =(readable with some difficulty), and signal strength was 3=(weak), and based on what Dean was reporting, my signal back to him was the same - 33.

73 to you both.

Rick - N3FJZ.

Dean's Double First: First Ham Contact Is Also His First Homebrew Contact

  

Hi Guys,

    I just had my first QSO with my ZIA transceiver!  Contact was with W8ERN in Brighton Michigan, which is approximately 300 miles from my QTH in Nashville Indiana.  W8ERN said I was barely audible and was surprised that he could hear me at all.  Especially when he found out that I was running less than 5W on an end-fed wire.  From what I heard, band conditions were pretty poor due to a magnetic storm.

    Sorry I didn't get any video of the QSO.  I heard him calling CQ and just answered.  I didn't expect him to return my call.  Btw, this was my first QSO as an amateur.  I was a bit nervous, I don't know why.  I plan on installing a 40M dipole before winter sets in so, hopefully my signal will get out a little further. 

    I have one other question.  I am considering purchasing a used rig in the next few months.  What would either one of you recommend?  I am not abandoning my home-brewing but it would be nice to have a back up rig when conditions are bad.  My budget is around $200 or so, and I don't mind something that might need some repairs.  There is a hamfest in Fort Wayne(my hometown) next month, so I might go up there and do some shopping.

    Thanks again for all of your encouragement and knowledge.   

 

73's

Dean AC9JQ

------------------------------

 

Hi Dean,

 

Congratulations on your first contact on the TIA AND your 1st contact as a ham. Bravo. Time to have a real celebration. Get cracking on that antenna before you have snow on the ground!!!

 

W8ERN, Angelo is an outstanding amateur and and a real gentleman. He has a very interesting past life. I think he worked for Multi Elmac and Central Electronics. During the 1940’s to 1960’s these companies produced some of the best ham gear. The AF-67 Transciter and the PMR8 were used mobile and of course the CE 100V and 200V were the first No Tune vacuum tube transmitters. So you were talking to one of the radio gods.

 

Again Congratulations Dean --- Bravo.

 

73’s

Pete

 

--------------------------

 

Dean:

 

Wow that's great.  Indeed the band conditions are about as bad as they get.  So bad that they are seeing Northern Lights (Aurora) far south into the USA.  Give it a few days and you will find much better conditions.

 

My advice on a commercial rig: DON'T!  You may think that they'd do better when conditions are poor, but they really won't.  If you want a bit more power, build an amp for the TIA. 

You are off to such an amazing start as a true homebrew ham.  Stay on the homebrew path.  Build a completely homebrew station!  Congrats! 

73  Bill

Dean's Tiny Tia -- Hardcore Homebrewing

 

Hi guys,

I've been on kind of a building hiatus due to various issues, but after seeing the work being done with the termination insensitive amplifiers I had to start noodling again.....as Pete would say.  Well I have decided to build a TIA (ZIA according to Pete) SSB transceiver.  I've decided to homebrew everything including the DBM, crystal filter, and even the Si5351 module.  As I wait for more parts to come in, I wanted to show the 2 TIA amps and crystal filter assembly I've built.  I've included a screenshot of the pass band response through the amps and the crystal filter.  It looks the same in both directions and everything fits into an area of 2 x 2.5 inches.  With the space left on the board, I hope to be able to put my SBL-1 clones on as well.  I follow up as I get more completed.

73

Dean AC9JQ 

 

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

New VFO for the Frankenstein R2 Phasing Receiver

I've wanted to change the VFO in my R2 phasing receiver.  The AD9850 DDS VFO with a divide by 4  I-Q generator limited me to 160, 80 and 40 meters.  But an Si5351 chip will go up to 160 MHz.  With a divide by 2 I-Q generator, this should allow me to cover 160 through 6 meters. I got the Arduino, LCD and rotary encoder all working tonight.  Thanks to Thomas LA3PNA for the code, and to Tom AK2B for help with the Arduino. The Si5351 board that you see sitting atop the Arduino is the work of Dean AC9JQ.  Thanks Dean.  

The flip-flop and inverter IC's should arrive this week.  That will allow me to finish up this VFO conversion project.

On our 17th Anniversary: SolderSmoke Podcast #179 -- TENTH ANNIVERSARY SHOW -- A Walk Down Memory Lane

On August 21, 2005 Podcast #1 was uploaded to our old GeoCities host. Just prior to that Mike KL7R set up a Yahoo Mail account.  I still use it. Yahoo sent me an e-birthday card! 

I put our 10th Anniversary Podcast on the YouTube Channel today.  Click above. Show notes below 

---------------------------------

22 August 2015

YESTERDAY MARKED 10 YEARS OF THE SOLDERSMOKE PODCAST
-- A clip: The first minutes of SolderSmoke #1
-- A trip down SolderSmoke memory lane.
-- The SolderSmoke lexicon -- words and phrases we use (a lot).

BENCH REPORT

-- Pete's antenna project.
-- Pete's new Blog: http://n6qw.blogspot.com
-- Bill's big amplifier problem fixed thanks to Allison KB1GMX.
-- Six digit freq readout with an Altoids case.

THE Si5351 PHASE NOISE CONTROVERSY

-- ALL oscillators make noise.
-- Keeping things in perspective: It is 100 db down!
-- Observations and tests from LA3PNA, NT7S, and K0WFS:
http://k0wfs.com/2015/08/21/si5351-phase-noise-and-thd-tests-using-an-agilent-e4402b-spectrum-analyzer/

http://nt7s.com/2014/11/si5351a-investigations-part-7/

-- Try it, you'll like it! The benefits trying things on real rigs.

NEWS
Interviews on "QSO TODAY" with Eric 4Z1UG.
Horrible band conditions.
Looking at Saturn with telescope.

MAILBAG

Another recruit for the CBLA: Paul KA5WPL.
Ron G4GXO on Bell-Thorn and Eden9 SSB rigs.
Rupert G6HVY on Kon Tiki radio and Mr. Spock.
Mikele's Croation BITX rigs.
Dean AC9JQ's TIA.
Bryan KV4ZS will build an LBS receiver.
Dave Anderson give Pete good antenna advice.
Steve Smith moves in from the garage.
Pete has built 12 SSB transceivers. Intervention time?

------------------

Another BITX DIGI-TIA -- AC9JQ's (video)

Wow, Dean's BITX with Termination Insensitive Amplifiers (3 of them) sounds really nice. And this is with a homebrew ladder filter (see below).

 

I also like the way Dean makes his enclosures -- he uses scrap aluminum and 1/2" angle.  This might cause me to abandon the wooden cigar boxes.

  



Dean will now add the driver and PA stages and plans on following Pete's suggestion by making this a 20/40 rig. 

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

SolderSmoke Podcast #234: PSSST, KWM-1, VHF Woes, Mighty Midget, TinySA, 17-12 Dual-Bander Advice Needed. MAILBAG

http://www.gadgeteer.us/17SSB.HTM

SolderSmoke Podcast #234 is available: 

http://soldersmoke.com/soldersmoke234.mp3

Roots of SolderSmoke: The "Click and Clack" of ham radio? 

Influences: Jean Shepherd, CarTalk, Shortwave stations.

Steve "Snort Rosin" Smith WB6TNL?  No. Steve "Aching Sinus" Smith WA6SOC  

Pete's Bench:
PSSST Super Simple SSB -- 7 Transistors. Switching IF Module: 

PSST Details:  https://www.n6qw.com/PSSST_20.html
DC RX.
KWM-1 Resurrection "Shame Shelf".
How to make things work:

http://n6qw.blogspot.com/2021/10/how-to-make-things-work-tribal.html
Diode Switching or Relays?

(Why the T/R diodes in the BITX 20 amplifiers?)
National Receiver.

Bill's Bench
Farhan's Talk to RSGB got me thinking of VHF 2 meter AM.
2 meter Benton Harbor lunchbox madness. SuperRegens Super Strange.
I broke my Maplin AF Sig Gen in the process. Fixed it.
Playing with MMMRX again. Put in 6 kHz ceramic filter. Sounds great SSB and AM.
Swept IF with noise, TinySA, and NanoVNA. Need better noise gen.
Mod to listen with TinySA (on blog).
Thinking of 17 meter /12 meter Dual-Bander IF around 21.4, VFO around 3.41 Mhz. Thoughts?
Sweeping double half lattice filter from Swan 240.  UGLY.  

MAILBAG:
--- ROOTS OF MAILBAG: Radio Moscow, Havana Cuba, HCJB, others.
-- Thomas K4SWL of the SWL Post: Could have been worse! Stairbag?

-- MY NOVICE LOG -- Heard back from ex-WN2RTH ex-WN2FLK ex-WB2RKK.
-- Drew N7DA worked Wes W7ZOI in Sweepstakes. FB.
-- Peter VK2EMU The movie Frequency and the Magic of Heathkits. Good, but not that good!
-- Thomas KK6AHT! Our old friend. Minima! Now has a young son! FB
-- Chuck WA7ZZE Saw QST profile. Sympathizes with Two-er trouble.
-- Tim M0CZP. Spell corrector. Vatican Diodes. Infallible!
-- Ramakrishnan VU3RDD Working on a NORCAL and a noise cancellation arrangement.
-- Skip NC9O said I was 40 Hz off on 17. But he had a reason to KNOW!
-- Steve K9NVD Glad he's a listener.  
-- Bob KY3R Novice Nostalgia. Should he use 75 watt bulb for dummy load? Yes! 
-- Todd K7TFC Video about why solder smoke goes into the face.
-- Anthony VU3JVX  Homebrew Antuino. I ask for help in moving freq to 450 kHz.
-- Jack NG2E Building Pete's DC RX.
-- Scott WA9WFA HBR-13 and MMMRX.
-- Stephen 2E0FXZ also got a FT-101 VFO.
-- Bob K7ZB on the air with 56 mW and a big antenna.
-- Dean AC9JQ Retired.
-- Allan WA9IRS Right to Repair update.
-- Farhan Invited us to Lamakaan ARC, Dec 11 or 12. Will be on QO100 Satellite Live! 

-- Many suggestions about my Apollo 11 Time Capsule. Still looking for ideas.

Happy Thanksgiving to all who celebrate this holiday!

https://shortwavearchive.com/archive/lsn2565kv5vg2l7s5qanx1mbnwvce5#commenting

SolderSmoke Podcast #179 SPECIAL TENTH ANNIVERSARY EDITION

SolderSmoke Podcast #179 is available:

22 August 2015

http://soldersmoke.com/soldersmoke179.mp3

YESTERDAY MARKED 10 YEARS OF THE SOLDERSMOKE PODCAST

-- A clip: The first minutes of SolderSmoke #1

-- A trip down SolderSmoke memory lane.

-- The SolderSmoke lexicon -- words and phrases we use (a lot).

BENCH REPORT

-- Pete's antenna project.

-- Pete's new Blog:   http://n6qw.blogspot.com

-- Bill's big amplifier problem fixed thanks to Allison KB1GMX.

-- Six digit freq readout with an Altoids case.

THE Si5351 PHASE NOISE CONTROVERSY

-- ALL oscillators make noise.

-- Keeping things in perspective:  It is 100 db down!

-- Observations and tests from LA3PNA, NT7S, and K0WFS:

http://k0wfs.com/2015/08/21/si5351-phase-noise-and-thd-tests-using-an-agilent-e4402b-spectrum-analyzer/

http://nt7s.com/2014/11/si5351a-investigations-part-7/

-- Try it, you'll like it!  The benefits trying things on real rigs.

NEWS

Interviews on "QSO TODAY" with Eric 4Z1UG.

Horrible band conditions.

Looking at Saturn with telescope.

MAILBAG

Another recruit for the CBLA:  Paul KA5WPL.

Ron G4GXO on Bell-Thorn and Eden9 SSB rigs.

Rupert G6HVY on Kon Tiki radio and Mr. Spock.  

Mikele's Croation BITX rigs.

Dean AC9JQ's TIA.

Bryan KV4ZS will build an LBS receiver.

Dave Anderson give Pete good antenna advice.

Steve Smith moves in from the garage.

Pete has built  12 SSB transceivers.  Intervention time? 

Our book: "SolderSmoke -- Global Adventures in Wireless Electronics" http://soldersmoke.com/book.htm Our coffee mugs, T-Shirts, bumper stickers: http://www.cafepress.com/SolderSmoke Our Book Store: http://astore.amazon.com/contracross-20

Arduino, Si5351, GPS linked atomic clock, GPS disciplined frequency counter and more...

Wow, it has been a while since I first talked to Rick, N3FJZ.  Above you can see his QSL card.  And here is a link to a SolderSmoke blog post (with videos) that describes our Homebrew to Homebrew contact:

http://soldersmoke.blogspot.com/2015/10/hb2hb-n3fjz-n2cqr-si5351-and-bitx-tias.html

The e-mail below shows that Rick continues to melt solder, bringing into his rigs some very cool technology:  atomic clocks, GPS modules, and color displays.  That's a long way from the original PTO Direct Conversion receiver that he first heard me with.  FB Rick! 

--------------

Leif, 

I've made great progress on my Arduino Mega 2560 based rig controller I call the ZX-Front-Panel. I just finished a feature I always wanted which is a built-in *GPS disciplined frequency counter*. It uses the 1-pulse-per-second timing output from the GPS module to create a frequency counter with atomic-clock accuracy. It's on the solderless breadboard with the rest of the ZX-Front-Panel right now, and even so, it can count up to 30MHz with no trouble! and it should be able to count up to 100MHz or more if built on a ground plane with a little shielding. The best part about it is that it only required one additional chip (a 74LV8154 32-bit counter $1 from Mouser) in addition to the existing parts already on the ZX-Front-Panel; i.e. the Arduino Mega 2560 ($10), the Ublox NEO-6N GPS module ($15), the display ($25), and the Si5351 PLL RF Oscillator ($8). 

Check out my video series covering the ZX-Front-Panel development progress. The first link below will bring up the video page on my website with the latest video at the top, so you'll have to scroll down a bit to get to the earlier development stages. Check out the rest of the website too for the schematics of my Bitx / TIA inspired rig design (which I call the ZX-SSB-II) that I used an early version of to make my first HF HB2HB contact with Bill (N2CQR) back in 2014 or so (Bill and Pete, via the Soldersmoke podcast, were my inspiration to build my first SSB homebrew rig). 

YouTube videos: http://www.remmepark.com/circuit6040/ZX-SSB-II-Front-Panel/ZX-SSB-II-Front-Panel.html#video 

Homepage: http://www.remmepark.com/circuit6040/index.html

Dean AC9JQ and I have been communicating via emailing about his progress in building his own copy of the ZX-Front-Panel, and I'm very excited to learn that he might be thinking about producing a future homebrew rig featuring the ZX-Front-Panel as its controller/VFO. The best thing about the ZX_Front-Panel is that ounce you install the sketch into the Arduino Mega, you don't need to modify the Arduino sketch itself when you build your rig; i.e. the SSB crystal filter's center frequency (the I.F. frequency), the Si5351's clock output drive level, the display brightness and contrast, and the Si5351 crystal correction factor (crystal trim) are all configurable, real-time, right from the ZX-Front-Panel's user interface, and once set, can be saved to the Arduino's non-volatile EEPROM to be automatically loaded on the next power-up. Also, since it has a GPS module, it features a UTC/Local real-time clock with atomic clock accuracy too. 

Anyway that's all for now, take care Leif. 

73 Rick.