Just go to http://soldersmoke.com. On that archive page, just click on the blue hyperlinks and your audio player should play that episode.
http://soldersmoke.com
Wow, lots of wisdom in this video from Leo Fernekes. Great hints and kinks on prototyping with copper clad boards. I need a Dremel just so that I can make Leo's board cutter. And I can see that I need some of that liquid flux and isopropyl alcohol. Surf boards and headers! Who knew? Teflon coating for the wires -- gotta get it. Glad to see that Leo is also a fan of copper tape. His emphasis on the importance of stage-by-stage construction and testing is right on the mark. My only disagreement with Leo is about his use of steel wool. I've found that steel wool will inevitably cause little tiny "Murphy Whiskers" to float around your workbench. They will eventually settle onto the most inconvenient and damaging place on your board. So I have banished steel wool from my workshop. Those green, non-metallic Scotch Brite pads work just as well and don't cause shorts. Three cheers for Leo. He is based in Thailand. He has an interesting background and some really amazing projects and insights: http://www.luminati.aero/leofernekes
Great video, I watched it when he first posted it and just watched it again it is so good. For liquid flux for small projects I like the Kester flux pens like this https://www.amazon.com/dp/B004X4KOWS
Thanks for this Bill - I hadn't heard of Leo before. What an amazing teacher. His indestructible continuity checker is a marvel of simplicity - I am going to build one because it is cool!
Lots of really good stuff here but heed Bill's advice. Don't go near wire wool. A better alternative would be a small block of Garryson "Garryflex" abrasive blocks (240 grit). It's the least course. It cleans copper board wonderfully - and it lasts and lasts.
My favorite topic from this video was his advice on reducing "mental" or cognitive load by labeling connectors, etc. That theme is almost endlessly expandable.
It looks like Leo is just starting his channel. There's seven videos there, and I hope he makes a lot more. BTW, it looks like he was using the steel wool on a kitchen or bathroom counter rather than in his lab.--Todd K7TFC
"SolderSmoke -- Global Adventures in Wireless Electronics" is now available as an e-book for Amazon's Kindle.
Here's the site:
http://www.amazon.com/dp/B004V9FIVW
The POTA Babe Goes Back to Florida – Day 1
-
In pursuit of my 60 new-to-me park activations, I headed back to Florida
for six days the first week of April. The weather forecast looked promising
– high...
Re: Heathkit DX-60A transformer
-
The original DX-60 used dual filament windings, one fed the DX-60 and the
other was brought out to the VFO socket. Maybe they used the leftover
transforme...
April 17, 2024. Something you can build.
-
Check N2CQR's Solder Smoke Daily News posting yesterday for a really super
neat Direct Conversion Receiver project (DCR) from Geoff, N6GWB. One of the ...
New Podcast from the Wireless Innovation Forum
-
Many thanks to SWLing Post contributor, Dennis Dura, who shares the
following news item from EIN Presswire: Wireless Innovation Forum Launches
“Beyond the ...
An Inline RF Step Attenuator for QRPp Work
-
I don’t need to explain the attraction of low power operation; if you’re
reading this, the chances are that you are already a convert. I’ve been
operating ...
Using an external clock with the RX-888 (Mk2)
-
*The RX-888 (Mk2) and external clocking*
*Figure 1:*
The RX-888 with external clock input *(right)*
The enable/disable switch is barely
visible behind the...
A 51S-1 Restoration Story
-
I came across my Collins 51S-1 in a big junkyard in Ankara, Turkey around
2012. It was in a pile with a lot of other electronic scrap, probably from
one o...
New QRP Cluster Online From OM0ET and OM6APN
-
By DX EXPLORER
DX EXPLORER
Paul OM0ET and Peter OM6APN recently launched a new cluster dedicated to
QRP operations. Have a look and I hope you will enjoy...
3D Printing The Hadley 114mm Newtonian Telescope
-
Yes, we’re building a 3D Printed Newtonian Telescope called Hadley. It’s
being printed in PETG and in the video below, I give a quick tour. My build
isn’...
3D printed project boxes
-
I have been busy with some other things that have kept me away from
electronics projects for quite a while. Now I can get back to them, but
realize I n...
Daylight Again – An all Analog Radio
-
What’s all this? In 10 seconds, A high performance, 7MHz, 5 watt SSB rig
Draws just 24 mA of current 90 dB dynamic range, 80 dB close-in dynamic
range 3D ...
Adding Enclosure to your sBitx Boards Order
-
The early buyers of the sBitx board set who bought it for $270 USD might
want to also add the enclosure (box) for in the kit. What you will now get
is a f...
Digi-chirp! Digital synthesis of ‘nostalgic’ CW
-
The bottom ends of 80, 40 and 20m are not what they used to be. For
starters, the busiest part is the digital segment where computers talk to
computers – l...
-
A Simple Speech Processor
(For QRP/SSB Homebrew Transceivers )
Over the last few weeks I had been thinking to build a small AF speech
processor to add to...
A New Look for your uBitx!
-
Adding a "Cool Blue" Display to your uBitx!
The standard "green background" with black lettering frequently reminds me
that I suffer from Chronic seasickn...
Posts
.jpg)
Great video, I watched it when he first posted it and just watched it again it is so good.
ReplyDeleteFor liquid flux for small projects I like the Kester flux pens like this https://www.amazon.com/dp/B004X4KOWS
Thanks for this Bill - I hadn't heard of Leo before. What an amazing teacher. His indestructible continuity checker is a marvel of simplicity - I am going to build one because it is cool!
ReplyDeleteLots of really good stuff here but heed Bill's advice. Don't go near wire wool.
ReplyDeleteA better alternative would be a small block of Garryson "Garryflex" abrasive blocks (240 grit). It's the least course. It cleans copper board wonderfully - and it lasts and lasts.
72/3
Tony G4WIF
My favorite topic from this video was his advice on reducing "mental" or cognitive load by labeling connectors, etc. That theme is almost endlessly expandable.
ReplyDeleteIt looks like Leo is just starting his channel. There's seven videos there, and I hope he makes a lot more. BTW, it looks like he was using the steel wool on a kitchen or bathroom counter rather than in his lab.--Todd K7TFC
Thanks for sending me down a very happy rabbit hole for a morning. What a great set of videos Leo has on his blog.
ReplyDelete