Just go to http://soldersmoke.com. On that archive page, just click on the blue hyperlinks and your audio player should play that episode.
http://soldersmoke.com
Here I take my Drake 2B -- arguably the quintessential Hardware Defined Radio -- and connect its first Intermediate Frequency circuitry to an RTL-SDR Dongle, allowing me to digitally process, filter, and display (panoramically!) the signals being inhaled by the ancient receiver. Another cool tech twist: To get at the 455 kHz IF signal I use the "Q-Multiplier" jack on the back of the receiver. This connector was put there to allow for the use of a selectivity enhancing regenerative stage. So I'm using that connector for a similar purpose, but using technology that wasn't even being dreamed about when that Drake 2-B was being designed in 1961.
Actually, the field of digital signal processing was well understood when the 2B was in its prime. The work of Nyquist, Shannon, and others was published as early as the 1930's. The only thing we lacked was the compute power. That is now available in tiny, low power DSP chips, enabling the things we're about to start taking for granted. We live in interesting times...
And even then a lot of what's being done existed in analog. Webb had that article in CQ in 1957 or 58 about building a synchronous detector, and that's now implemented in digital processing. It wasn't anything but a sideband slicer with the ability to synchronize with the AM signal.
Both might have used that jack in 1961, though they'd lose out on the good selectivity further on.
Of you don't know about the analog work, you'll never know to implement them with DSP. When PLLs hit in the early seventies (well they existed, and were discussed earlier, but were bulky with tubes), there were lots of methods described for better AM reception, including some that had no problem with DSBsc.
That said, there is something quite appealing to using one of these gizmos to replace selectivity and detectors in an existing receiver. Beats matching resistors and capacitors analog phasing networks. And there the receiver is offering front end selection, which is obviously lacking in these gizmos, and which I can't believe is taken care of on such cheap gizmos.
"SolderSmoke -- Global Adventures in Wireless Electronics" is now available as an e-book for Amazon's Kindle.
Here's the site:
http://www.amazon.com/dp/B004V9FIVW
Bill's OTHER Book (Warning: Not About Radio)
Click on the image to learn more
Where are the readers of SolderSmoke Daily News?
Pete Juliano N6QW
Master Homebrewer
Dean Souleles KK4DAS
With beret and with a Michigan Mighty Mite in hand
Re: BUNKEROFDOOM.com site??
-
I'll have to explore InMotion again, I have not had time to do it in any
depth due to lots happening around here. QTH has the sketch-mark (*) after
'unlimi...
FreeDV Sunday Morning Australian net - 10 stations
-
We've just had the FreeDV Sunday morning net (starts at 10:30am eastern
time) and 10 stations were at least seen.We had VK3TPM, VK3RV, VK5KVA,
VK2BLQ, VK3L...
New 20M SSB Hybrid Wireless Rig Topology.
-
Following the decision to start another Hybrid SSB rig, it might be well to
elaborate on some of the details. The first detail entails refining some of
the...
WA2TBQ
-
Episode 527 - Ron Demcko - WA2TBQ Ron Demcko, WA2TBQ, found his way into
electronics—and later amateur radio—thanks to the early influence of his
older bro...
The Communicator July - August 2025
-
*A Big One to Last the Summer*
We're coming up to our club's 50th Anniversary and this is another big
issue, with a look back at our history, great article...
A Real ZN414!
-
Recently, I built a simple little TRF receiver for the AM broadcast band
using a TA7642, a modern equivalent for a chip that was quite popular with
electro...
The "George Batterson 1935 CW QSO Party" - Summary
-
The first *George Batterson CW QSO Party* has concluded and the results are
in! The "*GB*" was introduced to honor George Batterson (W2GB), who along
wi...
KK4DAS MB 20 Transceiver Complete
-
The MB 20 transceiver is now complete. The rig is a homebrew 10-watt
20-meter SSB transceiver. The VFO module was an ebay purchase of a
salvaged Yeasu...
A Curious 9 MHz Crystal from Mouser Electronics
-
Just a quick post to share info about a good 9 MHz crystal sold by Mouser
Electronics.
I last purchased batches of crystals for xtal IF filters back in 2...
40m Pelican Case SSB Transceiver
-
See YouTube channels for details:
http://www.youtube.com/c/CharlieMorrisZL2CTM
*Test code for the LCD and Si5351*
#include
...
Hollow-State Design, 3rd Edition
-
Hollow-State Design, 3rd Edition is available from: Lulu Press:
tinyurl.com/hollowstatedesign3 eBay: search for “hollow-state design”
Electric Radio bookst...
I Finally Bought My Dream Airplane
-
Aviation has been a love of mine since I was a very little person. Living
in Nevada, seeing posters and ads for the Reno Air Races, specifically the
Texa...
Daylight Again – An all Analog Radio
-
What’s all this? In 10 seconds, A high performance, 7MHz, 5 watt SSB rig
Draws just 24 mA of current 90 dB dynamic range, 80 dB close-in dynamic
range 3D ...
Modifications to the Dayton/FDIM-2019 Antuino
-
The Dayton Antuino has sub-optimal performance. This is a short note on
improving it to an 80 db range of measurements. The trouble with Antuino
2.0 (the o...
Raduino as NBFM TX
-
Here is a neat, 30 minute hack for your Raduino to turn the Si5351 into a
pretty stable, solid NBFM transmitter. The hack is to add a varactor diode
in ...
QRP Labs shop!
-
[image: Shop]
All QRP Labs kits may be ordered online securely at the shop, with PayPal
payment.
*Click here to visit the shop!*
*Click!*
*Shop! Order...
Posts
Actually, the field of digital signal processing was well understood when the 2B was in its prime. The work of Nyquist, Shannon, and others was published as early as the 1930's. The only thing we lacked was the compute power. That is now available in tiny, low power DSP chips, enabling the things we're about to start taking for granted. We live in interesting times...
ReplyDeleteAnd even then a lot of what's being done existed in analog. Webb had that article in CQ in 1957 or 58 about building a synchronous detector, and that's now implemented in digital processing. It wasn't anything but a sideband slicer with the ability to synchronize with the AM signal.
ReplyDeleteBoth might have used that jack in 1961, though they'd lose out on the good selectivity further on.
Of you don't know about the analog work, you'll never know to implement them with DSP. When PLLs hit in the early seventies (well they existed, and were discussed earlier, but were bulky with tubes), there were lots of methods described for better AM reception, including some that had no problem with DSBsc.
That said, there is something quite appealing to using one of these gizmos to replace selectivity and detectors in an existing receiver. Beats matching resistors and capacitors analog phasing networks. And there the receiver is offering front end selection, which is obviously lacking in these gizmos, and which I can't believe is taken care of on such cheap gizmos.
Michael
Well done Bill.
ReplyDeleteHow about a diagram for the impedance changing device?
ReplyDelete