A Contact with my Old Azorean DSB Transceiver

I've been thinking about balanced modulators, and I wanted to see how some of my early circuits performed.  So I pulled this OLD Double Sideband rig off the shelf and fired it up. The balanced modulator -- and everything else! - worked fine,  and I soon made contact on 17 meter SSB with Gene, AB9GK. 

This was the first DSB transceiver that I ever built.  I made this out in the Azores, probably in 2000 or 2001.  Years later I had replaced the RF power amplifier with a "JBOT" (Just a Bunch of Transistors) designed by Farhan.  

Over on my YouTube channel a comment came in from my friend Jack:  

@dhakajack

"Looking inside and seeing the o-scope probe in place while the radio was on the air reminded me of neurosurgery where the patient is awake and talking while the surgeon probes different brain regions soliciting feedback. Sure, ham radio isn't neurosurgery, but it's not too far at times. Also, you already have rocket science covered."

Here is an article about my build of that first rig:

https://www.gadgeteer.us/17METER.HTM

I think the article captures well the trials and tribulations faced by new homebrewers, perhaps with the twist that comes from being out in the middle of the Atlantic ocean.  

Mike WU2D is having similar fun with his homebrew 10 meter DSB transceiver: 

https://www.youtube.com/watch?v=uZt1LTGyoHc

I was struck by how similar Mike's early QSO experiences were with mine.  We both put our DSB transmitters on the air before they made their way into real cabinets or boxes. 

Here's mine from 2001 in the Azores: 

Innovation and a Dual Band Sweep with Version 2 of the 15-10 Transceiver

Here are a couple of videos on Version 2 of my 15-10 SSB transceiver.  In the video above I try to show the advances and innovations that have been made since the start of my BITX construction adventure back in 2013.  

 The video below shows the receiver in action this morning on 15 and 10 meter SSB.  I think it sounds pretty good. 

Click on the image for a better look

Farhan asked what the passband of the 25 MHz crystal filter looked like.  I sent him this.  I think it looks very good, and shows that it is possible to use an IF this high.  This permits us to not only set up the transceiver for dual band coverage (in this case 15 and 10 meters), but it also allows for a lower frequency VFO (in this case around 3.5 MHz) with a resulting increase in VFO stability.  

SolderSmoke Podcast #250 Dean KK4DAS joins Pete N6QW and Bill N2CQR

SolderSmoke Podcast # 250 is ready for download: 

http://soldersmoke.com/soldersmoke250.mp3

VIDEO VERSION: (1707) SolderSmoke Podcast #250 -- With Pete N6QW, Dean KK4DAS, and Bill N2CQR - YouTube

Intro:   Welcome to Dean KK4DAS.  For 2024 Pete and I hope to jazz things up a bit by bringing in fellow homebrewers to talk about their projects.  Dean is our first victim.  Welcome Dean. 

Some good news:  Several new homebrew receivers are inhaling:  Armand WA1UQO in Richmond has an amazing looking regen.  Scott KQ4AOP in Tennessee got his DC RX working.  Mike AG5VG in Texas has been homebrewing BITX 20s and BITX 40s.  All are on the blog.  

Pete's report: 

-- Recent blog entries on filters,  SSB rig architecture, and of course digital VFOs. 

-- Phasing measurements, quadrature, and the Seeed Xiao RP2040

-- Error in QST article on early SSB transceiver.  ANOTHER ERROR!

--LC VFO on blog!  FB Pete!  

Dean's report:  

-- Tales of woe on the homebrew sBITX

-- Help from Farhan.  

-- Ground Bounce.  FFT Hallucinations.   Wisdom files.

SHAMELESS COMMERCE DIVISION:   

-- Whenever you are tempted to buy something from AMAZON, just start at the Amazon symbol on the right side of the page.  We get a cut from Bezos, and it doesn't cost you anything.  

-- You can try to do the same thing with E-bay.  We are finding a lot of great parts there. 

-- If you see a SolderSmoke post on Facebook,  please Like and forward. 

-- Become a patron!  Go to the Patreon page.  We put the money to good SolderSmoke use. 

-- Visit Mostly DIY RF and buy a PSSST kit!  

Bill's bench:  

-- Building yet another BITX dual bander.  15-10 again. Tried to use a 25 MHz filter left over from the earlier project, but I had to build another.  Built a new VFO using the variable cap and anti-backlash gear recommended by Pete.  Was a bit tough to get the receiver sounding good.   Had a diode ring as the second mixer, but went back to a singly balanced mixer. 

-- 10 meter AM -- Thanks to Jerry Coffman K5JC for mod. 

Other topics: 

--Counterfeit chips.  Why? 

MAILBAG: 

Wes W7ZOI 

Jim Cook W8NSA  Transoceanic BFO

Grayson KJ7UM -- Vintage Computer Museum

Chuck Adams --Glad to hear that Chuck is doing well.  

Frank Harris  K0IYE --  NO CHIPS!!!! 

ED DD5LP  Antenna software

Eldon KC5U  10 AM We  made a contact

Joh DL6ID  10 AM   

Phil   W1PJE of MIT   10AM   Where is L5? 

Bob WP4BQV now in UK 

Dino Papas KL0S in Wilmington   Reverse Polarity protection. 

AA7EE Dave Richards  Liked Armand's receiver

Rogier PA1ZZ  

Jonathan-san W0XO  Listened to my ET-2 CW Whoop,whoop

Nick M0NTV  Great videos from Nick the Vic

Will KI4POV  Working on his own SSB rigs.  

John West -- Who is the South American ham who made his capacitors and heat sinks? 

Ed KC8SBV  Working on DC receiver, experimenting with FETs 

Mike WN2A great contributions.  Si5351 sole source danger! 

Nick N3FJZ -- watch out for dead bands when testing receivers! 

Don KM4UDX encouragement from new Prez of VWS

Dave K8WPE Likes QF1 Cap backlash.  Says I'm getting soft! 

Dave WA1LBP My fellow Hambassador, from Okinawa USMC Sergeant with a workshop. 

Yet ANOTHER Homebrew 15-10 SSB Transceiver (Video #1)

A homebrew 15-10 SSB Rig for the Dominican Republic:

This is my second build of this rig.

I am using a 10 pole crystal filter that I built for the first build, but did not use. I am also using the tuning capacitor from a Galaxy V's oscillator -- I like the anti-backlash gears and the reduction drive. This rig is built on a pine board covered with adhesive copper tape. It has been built stage-by-stage on copper-clad boards using the Manhattan construction style.

The structure of the rig is basically that of a BITX rig -- the RF and IF amplifiers are Termination Insensitive Amplifiers.

Soon the receiver will be completed. I will then build the stages needed for the transmitter portion of the transceiver.

I will take this rig with me to the Dominican Republic.

Listen to this great contact with KA1BWO on 10 meter AM -- 1800 miles with 4 watts AM

Joe KA1BWO is a well-known AM operator who moved West to Idaho several years ago. We had a very nice contact on 10 meter AM on January 14, 2024.  See the video above. 

I was using an old CB rig that I had converted to legitimacy on 10 meters using the mod developed by Jerry K5JC:  

http://www.jcoffman.net/WB5RUA/10_meter_AM_conversion_w_Photos.html

I was running 4 watts on AM to a Hex beam. The signal path was over 1800 miles from Virginia to Idaho.

1000 Mile QSO with KC5U using Modified CB Rigs (video)

Eldon KC5U saw my blog posts about Jerry K5JC’s mods to the PLL02 CB rigs.

Here is the mod: http://www.jcoffman.net/WB5RUA/10_meter_AM_conversion_w_Photos.html

Eldon did the mod and we have been trying to make contact. We did so today. It was very cool. I was on my GE rig; Eldon was running a JC Penny! (See video above.) 1054 miles. Thanks Eldon. And thanks Jerry!

On my Second Day on 10 meter AM, I Worked K5JC -- the Creator of the Mod that I was Using (Video)

See video above.  This happened on my second day on 10 meter AM. I was using the little GE CB radio that I had modified for 10 meters. I had lucked out. First bit of luck: the CB that I bought (for parts!) at a hamfest turned out to be just the thing I needed for a quick and easy mod. The GE box had what is called a Hygain board and -- most important -- a PLL02 chip. Second bit of luck: I stumbled across an article by Jerry K5JC on how to put this particular kind of device onto 10 meter AM. Boom, Bob was my uncle, and I got on 10. Then, today, the miracle happened. I heard Benny K5KV and I gave him a call. He asked about my rig. I described the mod to the GE CB. Benny seemed kind of surprised, and for good reason. You see, Jerry K5JC (the guy who created the mod that I was using) had just broken squelch on Benny's rig! Benny told him to get on 10 and soon I as in contact with the guy who had created the mod that I was using. The Radio Gods Have Spoken. Thanks Benny and thanks a Jerry. This was all really cool.

Think of odds of this happening: On my second day on 10 AM, running just 4 watts, I just happened to contact Benny K5KV in Texas who just happened to be in 2 meter range of Jerry K5JC, who just happened at that moment to be breaking squelch on Benny's 2 meter rig. TRGHS.

Bill N2CQR Goes Citizen Band

 10-4 Good Buddies! 

Why Building for 10 Meters is Harder than Building for Lower Frequencies

Recently my trusty CCI EB63A .1kW amplifier has been in rebellion.  On 10 meters, it now often insists on being an oscillator.   It calms down nicely on 20 meters.  But on 10, it has been a rebellious beast.  

Why is this?  Why would an amplifier that is well behaved and stable on 20 meters behave so badly on 10 meters?    

I used LTSpice to explore the problem.  

I looked at two ordinary wires.  I gave them each a value of .003 uH.  Very low.  Then I joined them together in a transformer.  I put a 1 volt signal into the primary and looked (in LTSpice) at how much of a signal appeared in the secondary.  First, the result on 14 MHz.  About 250 mV appears on the secondary. 

Now consider what happens at 28 MHz.  Nothing else in the circuit changes.   Just the frequency.

Here we get about 450 mV.  A lot more.   

Realize that my little EB63A amp has lots of wires in it, most of which are ready to serve as primary or secondaries in circuits like this.  Increasing the frequency makes it more likely that a ginal will jump to someplace that it is not supposed to be.  Output will couple to input and the Barkhausen criteria will be met. The amplifier will become an oscillator.   

Of course, something similar happens with capacitive coupling.  Same story:  the higher the frequency, the harder it is to keep the amplifier stable. 

Don't worry:  Improved shielding is saving the day.  The amplifier is now stable on 10.   More about this in the next podcast... 

Working Indonesia and Chile with new 15-10 Homebrew Transceiver

Conditions were good this morning, and the Radio Gods continue to favor homebrew rigs.  I got on 15 meters SSB with the new 15-10 dual bander and quickly worked YH0AD in Jakarta (about 10,000 miles).  A few minutes later I talked to YB2MVD; he was a bit further east on Java.  I shot a video of the QSO with YB2MVD.  He said I was 59.  

I then switched to 10 meter SSB (same rig) and worked CE4PS in Chile (5,000 miles).   

TRGHS. 

The antenna for all these contacts was my K4KIO Hex Beam.  I was running about 75 watts from the .1kW CCI amplifier. 

Progress Report Video on my 15-10 Meter Homebrew SSB Transceiver

The receiver is mostly done on my 15-10 rig, and I am following Farhan's BITX20 advice: "pause at this point and listen to the receiver that you have built." In the video I mention a problem with out-of-band signals. I was hearing shortwave broadcast signals (Brother Stair!) and even strong 20 meter CW signals. I thought the problem may have been with the bandpass filters, but after thinking about it I focused on the diplexer coming out of the product detector. I put a simple diplexer (from W7EL's Optimized Transceiver) in there and the problem disappeared. I still plan on beefing up the Bandpass Filters -- the dual tuned circuits I have been using are, I think, inadequate. I needed some more space on the wood board so I installed a sort of "back porch" -- you can see it in the video. I will build a power amplifier (RD6 or RD16) and a mic amp. Soon I will be on 15 and 10 with this rig. On this one, I am going the full "radical fundamentalist homebrewer" route: no ICs, no manufactured PC boards, no VFOs from old Yaesus.

SolderSmoke Podcast #247 -- Hating on the IC-7300, Pete Goes FT-8 with a KWM-1, Bill's 15-10 Rig, MAILBAG

Bill's 15-10 Rig -- Click on image 

SolderSmoke Podcast #247 is available: 

Audio Podcast:  http://soldersmoke.com/soldersmoke247.mp3

Video:  (482) SolderSmoke 247 -- Hating on the IC-7300, Pete goes FT8 (with a KWM-1), Bill's 15-10 rig, Mailbag - YouTube

Bill’s Bench:

The 15-10 Dual Bander.

n  10 pole crystal filter at 25 MHz.

n  G3UUR, Dishal, AADE and all that..

n  Testing woes.  Looked bad.  But it was a bad test cable. Duh.

n  VFO (Colpitts) at around 3.5 MHz.

n  Buffer blues:  Bad J-310s.  Beware!  

n  Variable cap from a Heath Q Multiplier

n  A bit of a black art – competing goals. Freq coverage, etc.

n  BFO needed an amp to turn on the diodes in the balanced modulator

n  TIA amps.   SIX dual direction TIAs.  18 transistors.

n  On a pine board (like Frank Jones)

n  Will use the N6QW all discrete AF amp.

n  Maybe an RD16 in the final?

n  Will build a second one for the DR.

 Shameless Commerce:  Mostly DIY RF and the PSSST kit.  Todd K7TFC reports:  “The P3ST is on track for Lee Deforest's birthday release (August 26th). I'm going to send out another newsletter on July 4th, and I'll give some details on P3ST development.” Results of Todd’s Survey.

Pete’s Bench

n  FT-8 on the KWM-1!

n  Presentation to the ham club.

n  Why the Icom 7300 is the anti-thesis of homebrew.

MMAILBAG:

-- SPRAT 195  Summer 2023, in the mailbox.  A happy day at N2CQR

-- Armand WA1UQO sent a wonderful book about Faraday and Maxwell… And told me Jim K8OI was heading to our area.  I met Jim at the VWS Field Day event.  FB.  Thanks Armand.

-- Tony G4WIF sent Father’s Day greetings.

-- Alvin N5VZH asking about electrolytics for his 2-B.  Hayseed Hamfest!

-- John AC2RL replacements for the IBEW.  We need to start over!

-- Steve “Snort Rosin” Smith WB6TNL was in the area.  Sorry I missed him.

-- Joh DL6ID helping us to track down origins of a homebrew receiver Grayson saw in Berlin.

-- Grayson KJ7UM was in Europe visiting his wife’s relatives.  But I think he is back in the USA.

-- Walter KA4KXX sent a QRP HB family portrait. 

-- Wouter ZS1KE sent info on surface mount soldering.

-- George Zaff KJ6VU Ham Radio Workbench – re-runs! Recommended audio processor.  Let me know how it sounds. 

-- Michael AA1TJ   Great to hear from him. 

-- Alan Wolke W2AEW on the toroids  he used in Diode Ring video.  Thanks Alan!

-- Dean KK4DAS, AI and SWR meter project  And new lexicon word:  Hamsplaining. 

-- Bob N7SUR --  Let me know we are semifinalists in the Hack-A-Day prize!  

The 15 - 10 rig from above -- Click on image

SolderSmoke Podcast #246: PeteGPT! DC RX, Si5351, Franklin osc, Cuban DSB, Hex beams, uBITX mods, DX, 10 meters, MAILBAG

 

SolderSmoke Podcast #246 is available: 

AUDIO PODCAST: http://soldersmoke.com/soldersmoke246.mp3

YouTube VIDEO: (247) SolderSmoke Podcast #246: uBITX, Hex Beam, DX, High School DC RX, 10 meter SSB Rig, MAILBAG - YouTube

The AI Deep Fake Threat!  PeteGPT!

Hearing Aid info:  I can hear the cymbals in my audiogram adjusted Airpods.

Update on the TJ DC RX project – Several receivers working! https://hackaday.io/project/190327-high-schoolers-build-a-radio-receiver

Sunil’s company provides Nano/Si5351 combos.  With the KD8CEC software. Very cool.  http://amateurradiokits.in They have a new SSB dual band transceiver – the Airpal.

Mark AJ6CU helping me. Sent me Nanos with KD8CEC software. His uBITX Settings Editor seems very cool. https://github.com/AJ6CU/uBITX-Settings-Editor/releases/tag/V2-beta-1  Thanks Mark.  

Franklin Oscillators. 

Cuban Islander and Jaguey info.  Send more!

Fixing up uBITX 2   How Bill blew up TWO Raduino Nanos. My results with the KB1GMX mods. (see below)

Hex Beam work:  Adding 10 and 15 meter elements.  But now I can hear AM breakthrough from WFAX 1220 AM  (5 kW during the day),  So I made a high pass filter.

Made first contacts on 15 and 10:  Argentina, Brazil, Dominican Republic.

First contacts with both India VU3TPW and China BA4TB.  SSB homebrew.

sBITX news. Taking orders!

Pete’s 10 Meter SSB Project

Mailbag:

--Wes W7ZOI provided great info and analysis on the Franklin oscillator. And lots of great tech info on other topics: http://w7zoi.net/oldtech/ponder.html Thanks Wes!
--Lex PH2LB. uBITX mods. TO-18 Heatsinks. New stickers (see above).
--Kostos SV3ORA and Hans G0UPL about the Franklin Oscillator.
--Listening to HRWB 178: Great stuff, many old friends: George KJ6VU moved to Oregon. Thomas K4SWL on the show.  Ben, an old friend of Pete’s,  mentions John Zaruba K2ZA – the guy who gave me the DX-100. Wonderful connections.
--Thanks to Todd VE7BPO for sending me another AADE LC meter. I need it for the SSSS.
--Nick MONTV planning a 15/10 meter dualband SSB rig. Me too! See video.
--Trevor Woods in W. Australia – The portrait in Artie Moore’s shack. Chuck WB9KZY – Willam Ramsay
--LA6NCA Helge three tube RX. Regen or DC? Mike Masterson WN2A and I discuss.
--Mike WU2D video on Retro QRP rigs – Steve G0FUW discusses Severn rig long in the works –started 1983 and nearly finished!
--Tim Hunkin of Secret Life fame did video with speaker made from potato ship bag. Discussed with Tony G4WIF and others. Also, Tim has an amazing video on cutting holes in metal. On the SolderSmoke blog.
--Bob Crane W8SX will be covering FDIM for SolderSmoke!
--Glen VE3DNL working on a more sophisticated DC RX.
--Craig KC2LFI from the beach on Grand Cayman. FB.
--Steve EI5DD reports We have changed our name - The May Issue of the HAM RADIO IRELAND Magazine, Ireland’s only independent magazine for the Radio Experimenter: https://docdro.id/SHH0VEy
--Mike EI0CL on 15 meters with Dean KK4DAS. FB
--Howard N3FEL of the Penn Wireless Association wants to do a group build of a DC RX.
--Martin LW9DTR in Buenos Aires looking for help with the code for an AD9850
--Todd K7TFC – always helping other homebrewers.
--Really thoughtful message from Kevin WN7Z

uBITX 2

My KB1GMX mods to uBITX 2

On Ten Meters with a uBITX from the Eastern Tip of Hispaniola

On ten from HI7.  Cluster spots, DX, CW, and the Reverse Beacon Network. 

 

10 Meter Quarantine QSOs near Boston -- KC1FSZ's Peppermint 10

Hi Guys:

I hope all is well.  Thanks for the more frequent episodes!

I’ve not submitted anything lately but I’m still doing a lot of building.  Over the last few weeks I’ve been working to get myself on 10 meters.  There is some good local activity up here in the Boston suburbs on 10.  The result of this effort is the next in the Peppermint Line of high-performance radio products for the discerning operator: The Peppermint 10.  This rig uses digital VFOs and puts out about 12 watts on a good day.  It works in conjunction with a direct-conversion receiver that has been modified for 10 meters.  The details are described in the write-up (see link):

https://mackinnon-public-web.s3.amazonaws.com/peppermint-10/index.html 

73s,

Bruce KC1FSZ